To configure source clocks on Exynos 5420 for MMC drivers.
Some registers are different from the 5250. FSYS now has two parts
and MMC uses FSYS2. The MMC block uses MPLL as the clock source.
The "high-speed" MMC interface runs as 52MHz, so divider is set
accordingly.
Also, the MMC driver has changed from MSHCI (Mobile Storage Host Controller
Interface) to DWMCI (DesignWare MMC Controller Interface).
BUG=chrome-os-partner:19420
BRANCH=none
TEST=emerge-peach_pit chromeos-coreboot-peach_pit
Change-Id: I9ba9cf43e2f2dcd9da747888c0c7676bd545177b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60858
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Data is intended to be a byte array, so it should be described by a type which
has a fixed size equal to an 8 bit byte. Also, the data passed to write
shouldn't be modified and can be const.
BUG=chrome-os-partner:19420
TEST=Built and booted into depthcharge on pit. Built and booted into ChromeOS
on snow.
BRANCH=None
Change-Id: Ib01c0218b95d8660418fea2181f6f38bc0675159
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/60601
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
1) fix enable of power aware interrupt routing
2) set BIOS_RESET_CPL to 3 instead of 1
3) mirror PKG power limit values from MSR to MMIO on all SKUs
4) mirror DDR power limit values from MMIO to MSR
5) remove DMI settings that were from snb/ivb as they do
not apply to haswell
BUG=chrome-os-partner:20604
BRANCH=none
TEST=manual:
1) verify power aware interrupt routing is working by looking
in /proc/interrupts to see interrupts routed to both cores
instead of always to core0
BEFORE: 58: 4943 0 PCI-MSI-edge ahci
AFTER: 58: 4766 334 PCI-MSI-edge ahci
2) read back BIOS_RESET_CPL to verify it is == 3
localhost ~ # iotools mmio_read32 0xfed15da8
0x00000003
3) read PKG power limit from MMIO and verify it is the same
as the MSR value
localhost ~ # rdmsr 0 0x610
0x0000809600dc8078
localhost ~ # iotools mmio_read32 0xfed159a0
0x00dc8078
localhost ~ # iotools mmio_read32 0xfed159a4
0x00008096
4) read DDR power limit from MSR and verify it is the same
as the MMIO value (note this is zero based on current MRC input)
localhost ~ # rdmsr 0 0x618
0x0000000000000000
localhost ~ # iotools mmio_read32 0xfed158e0
0x00000000
localhost ~ # iotools mmio_read32 0xfed158e4
0x00000000
Change-Id: I6cc4c5b2a81304e9deaad8cffcaf604ebad60b29
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60544
The workaround of re-opening device in exynos_spi_read has been fixed by the new
correct open/close and xfer procedure. It's safe to be removed now.
BUG=none
TEST=emerge-peach_pit chromeos-coreboot-peach_pit; # Successfully boot on pit.
BRANCH=peach_pit
Change-Id: I85d80a5298bbec09b4b731e83dd7bd1d97b3e039
Reviewed-on: https://gerrit.chromium.org/gerrit/60086
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Tested-by: Hung-Te Lin <hungte@chromium.org>
Switch spi_xfer and exynos_spi_read to use the new spi_rx_tx function.
BUG=chrome-os-partner:20441
TEST=emerge-peach_pit chromeos-coreboot-peach_pit; # Successfully boots on pit.
BRANCH=peach_pit
Change-Id: I46dae4d604c8b78bec5aaeb8778dfad635e657b1
Reviewed-on: https://gerrit.chromium.org/gerrit/60085
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Tested-by: Hung-Te Lin <hungte@chromium.org>
The SPI driver (exynos_spi_rx_tx) was implemented with only "read" ability and
only full-duplex mode. To communicate with devices like ChromeOS EC, we need
both output (tx) and half-duplex (searching frame header) features.
This commit adds a spi_rx_tx that can handle all cases we need.
BUG=chrome-os-partner:20441
TEST=emerge-peach_pit chromeos-coreboot-peach_pit
BRANCH=peach_pit
Change-Id: I4f216c42e2d9a1930e8c169e3cdd082ba7918357
Reviewed-on: https://gerrit.chromium.org/gerrit/60084
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Tested-by: Hung-Te Lin <hungte@chromium.org>
The original Exynos SPI open/close procedure was copied from U-Boot SPL with
some assumptions that only works in SPL stage. For example, it tries to always
work in 4-byte transmission mode with only RX data is swapped, and claims a
packet for initial address command (and with incorrect size).
This commit revises open/close and reset so only the required SPI registers are
configured.
BUG=chrome-os-partner:20441
TEST=emerge-peach_pit chromeos-coreboot-peach_pit
BRANCH=peach_pit
Change-Id: I8c16d539f6aebd14182846ced5afa7a9457890e4
Reviewed-on: https://gerrit.chromium.org/gerrit/60083
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Tested-by: Hung-Te Lin <hungte@chromium.org>
Fill the SPI device parameters for spi_setup_slave on Exynos 5420.
BUG=chrome-os-partner:20441
TEST=emerge-peach_pit chromeos-coreboot-peach_pit
BRANCH=peach_pit
Change-Id: I447e877332451a0172e2530f3f127343f8a730c3
Reviewed-on: https://gerrit.chromium.org/gerrit/60082
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Tested-by: Hung-Te Lin <hungte@chromium.org>
The SPI module in Exynos 5420 didn't follow Coreboot's SPI API standard
(spi-generic.h) and will be a problem when we want to share SPI drivers.
This commit replaces exynos_spi_* by spi_* functions.
Note, exynos_spi_read is kept and changed to a static function because its usage
is different from the standard API "spi_xfer".
BUG=chrome-os-partner:20441
TEST=emerge-peach_pit chromeos-coreboot-peach_pit
BRANCH=peach_pit
Change-Id: Iadd14bcedbe97aacecd490d97f6ca17c4097e4a5
Reviewed-on: https://gerrit.chromium.org/gerrit/60081
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Tested-by: Hung-Te Lin <hungte@chromium.org>
Add SPI0 and SPI2 to Exynos 5 SPI list, and correct structure names.
Also removed the un-enumerated devices (SPI_BASE, base_spi()).
BUG=chrome-os-partner:20441
TEST=emerge-peach_pit chromeos-coreboot-peach_pit
BRANCH=peach_pit
Change-Id: I059dbd778dc37633c59702050965632b7b22e685
Reviewed-on: https://gerrit.chromium.org/gerrit/60079
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Tested-by: Hung-Te Lin <hungte@chromium.org>
Some initialization / shutdown commands should be paired correctly in a SPI I/O
session. For example, setting CS should be enabled and disabled in each read;
and the bus width (byte or word) should be configured only when opening /
closing the SPI device.
BUG=none
TEST=manually: emerge-daisy chromeos-coreboot-snow; boot on Snow.
BRANCH=none
Change-Id: I1e4532e71fb535453c9fd9151f89dd2aca52e7d0
Reviewed-on: https://gerrit.chromium.org/gerrit/59691
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: Hung-Te Lin <hungte@chromium.org>
The functions which checked the status of a transfer would return success if
the bus was no longer occupied, even if it's no longer occupied because the
transfer failed. This change modifies those functions to return three possible
values, 0 if the transfer isn't done, -1 if there was a fault, and 1 if the
transaction completed successfully.
BUG=chrome-os-partner:19420
TEST=Built and booted into depthcharge on pit and verified that the PMIC was
initialized successfully by coreboot. Similar changes were tested in
depthcharge when probing the tpm and when communicating with it and corrected
some problems there.
BRANCH=None
Change-Id: If20e0f29688542ba03f08c1da3ebe0429103d33d
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/59733
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
The exynos manual suggests hooking the mmc ip blocks to the mpll. They had
been set to use a different pll. This changes them over and modifies the
divider so that the frequency stays the same.
BUG=chrome-os-partner:19420
TEST=Built and booted into depthcharge on pit.
BRANCH=None
Change-Id: I9b473b683c5806a49c9eba91807baa0b58c9c9dd
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/59732
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
This allows us to set different speeds for each HSI2C bus.
BUG=none
BRANCH=none
TEST=using logic analyzer on pit, saw I2C4 run at 1MHz
and I2C9 run at 400KHz
Change-Id: I27bf54084644c4cbcdbed423197a1113d6f6c17b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59693
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
This change adjusts some clock settings so that they match U-Boot. There are
three different changes.
1. Change the source for psgen from the oscillator clock to the pclk.
2. Change the pll feeding the SPI busses from epll to mpll, as suggested in
the manual.
3. Change the SPI prescaller.
BUG=chrome-os-partner:19420
TEST=Built and booted into depthcharge on pit.
BRANCH=None
Change-Id: I2896c099a91bdb78bfac03fbb804ef65c3233cd0
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/59730
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
The clock divider was being read from registers incorrectly which meant that
the periph rate was wrong.
BUG=chrome-os-partner:19420
TEST=Built and booted into depthcharge on pit.
BRANCH=None
Change-Id: Idb38374195a737fac2f096771929c8f1645d7247
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/59729
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Wait for UART FIFO to be ready.
(Credit to dhendrix for finding the bits to test with.)
BUG=none
TEST=manually boot device and see no garbage on serial output.
BRANCH=none
Change-Id: Ic921cc39a27b137f1a7fd137e032ffb61489bdd1
Reviewed-on: https://gerrit.chromium.org/gerrit/57660
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
... this is needed for libpayload to talk to USB devices.
(forward ported from https://gerrit.chromium.org/gerrit/#/c/55554)
BUG=chrome-os-partner:18635
TEST=Boot on Snow, see EHCI stack find devices
BRANCH=none
Change-Id: I2db8eb30ccc7983e2305b6222f02babf14ddb53f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/55811
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
... this is needed for libpayload to talk to USB devices.
BUG=chrome-os-partner:18635
TEST=Boot on Snow, see EHCI stack find devices
BRANCH=none
Change-Id: I663cb560d79e98cd2b767238fd4aec2cd04854e9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/55554
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The members data structures in dmc.h are intended to have a particular size.
Rather than assume that particular types are the right size, we should use
types that are guaranteed to be the right size. Also, since the registers are
at particular offsets as well, the structures should be packed.
BUG=chrome-os-partner:19420
TEST=Built for pit.
BRANCH=None
Change-Id: Ie52a5eba459bc2a070656b264e00ef783838026e
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/59237
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
The previous driver was a bit awkward and not entirely correct. This change
primarily replaces the read/write functions with simpler and more robust
(hopefully) version.
BUG=chrome-os-partner:19420
TEST=Built and booted on pit into the RAM stage without any errors reading or
writing registers on the PMIC. There isn't really any direct feedback from the
PMIC, so I'm assuming since it didn't complain it worked. I looked at some of
the transaction on an oscilloscope and they looked correct.
BRANCH=None
Change-Id: I01b1f9ea43eafb4aae1dbebddc051cd5ec5aea74
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/59201
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
For all other CPUs, we unconditionally include the CPU Kconfig
files in the CPU directory, not in the vendor directory. Do the
same thing for the Exynos CPUs. This allows us to make CPU dependent
changes in the directory of that CPU alone.
Also, drop some unused Kconfig variables from the Exynos Kconfig
files.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
BUG=chrome-os-partner:18637
TEST=no functional change
BRANCH=none
Change-Id: I57667dc5c5af5f61a54186a8fd47ceeae143d688
Reviewed-on: https://gerrit.chromium.org/gerrit/59291
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
This updates the low-level I2C code to handle the new high-speed
HSI2C/USI inteface. It also outputs a bit more error information
when things go wrong. Also adds some more error prints. Timeouts
really need to be noted.
In hsi2c_wait_for_irq, order the delay so that we do an initial
sleep first to avoid an early-test that was kicking us out of the
test too soon. We got to the test before the hardware was ready
for us. Finally, test clearing the interrupt status register every time
we wait for it on the write. Works.
BUG=chrome-os-partner:19420
BRANCH=none
TEST=TODO...
Change-Id: I785a4b9038d25c1a564784da0b7d54eaa9ef651d
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/58761
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
We saw a problem on x86 last year in which setting direction, then value,
glitched the output and caused problems. Change this code to set the output,
then the direction.
BUG=chrome-os-partner:19420
TEST=Build and boot on pit.
BRANCH=None
Change-Id: Ie40786139b0b496e22a80dc3dd712b6adff03d1e
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/59087
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
The 5420 clock code still had a data structure in it for the 5250 clock
registers which was used by some of the clock functions. That caused some
clocks to be configured incorrectly, specifically the i2c clock which was
running at about 80KHz instead of about 600KHz as configured by U-Boot.
Also, the registers and bit positions used to set up the SPI bus were not
consistent with U-Boot, and if the bus clock rate were set to 50MHz, a rate
which has historically worked on snow, loading would fail. With these fixes
the clock rate can be set to 50MHz and the device boots as much as is
expected. I haven't yet measured the actual frequency of the bus to verify
that it's now being calculated correctly.
BUG=chrome-os-partner:19420
TEST=Built and booted on pit and saw that the SPI now works at what is
nominally 50MHz, and that the I2C bus connected to the PMIC is running at the
same frequency as it does under U-Boot.
BRANCH=None
Change-Id: I9fede9cd3defdff7cbb2a76bb0e0bf86967bebb7
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/59020
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Tested and working. Gets us to ramstage.
BUG=chrome-os-partner:19420
TEST=Build and boot on pit.
BRANCH=None
Change-Id: I603aec97155a468a12b3fd492521b5a4e7169f9e
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/57363
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
This adds entries for I2C8-10 to giant switch statement in
clock_get_periph_rate(). It also eliminates the I2C peripheral's
usage of clk_bit_info since it's confusing and error-prone.
BUG=chrome-os-partner:19420
BRANCH=none
TEST=TODO...
Change-Id: I4b006c034575e6bd1f4722503668b9a142020eb5
Reviewed-on: https://gerrit.chromium.org/gerrit/58782
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
BUG=chrome-os-partner:19420
TEST=Built and started booting on pit.
BRANCH=None
Change-Id: I06ea5dfdb1de2d32bd1f3b276f98617c0c3efc46
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/58788
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
The pinmux code for the exynos5250 was all bundled into a single, large
function which contained a switch statement that would set up the pins for
different peripherals within the SOC. There was also a "flags" parameter, the
meaning of which, if any, depended on which peripheral was being set up.
There are several problems with that approach. First, the code is inefficient
in both time and space. The caller knows which peripheral it wants to set up,
but that information is encoded in a constant which has to be unpacked within
the function before any action can be taken. If there were a function per
peripheral, that information would be implicit. Also, the compiler and linker
are forced to include the entire function with all its cases even if most of
them are never called. If each peripheral was a function, the unused ones
could be garbage collected.
Second, it would be possible to try to set up a peripheral which that function
doesn't know about, so there has to be additional error checking/handling. If
each peripheral had a function, the fact that there was a function to call at
all would imply that the call would be understood.
Third, the flags parameter is fairly opaque, usually doesn't do anything, and
sometimes has to have multiple values embedded in it. By having separate
functions, you can have only the parameters you actually want, give them
names that make sense, and pass in values directly.
Fourth, having one giant function pretends to be a generic, portable API, but
in reality, the only way it's useful is to call it with constants which are
specific to a particular implementation of that API. It's highly unlikely that
a bit of code will need to set up a peripheral but have no idea what that
peripheral actually is.
Call sights for the prior pinmux API have been updated. Also, pinmux
initialization within the i2c driver was moved to be in the board setup code
where it really probably belongs. The function block that implements the I2C
controller may be shared between multiple SOCs (and in fact is), and those
SOCs may have different pinmuxes (which they do).
Other places this same sort of change can be made are the pinmux code for the
5420, and the clock configuration code for both the 5250 and the 5420.
BUG=None
TEST=Built and booted Coreboot on Snow. Went into recovery mode and back.
BRANCH=None
Change-Id: Ib6f6921ffcf749da02e25519279d2dc7cbf8f2ec
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/58784
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
SPD GPIOs were being read prior to initialization in romstage_common. To
fix, pass the copy_spd function to romstage_common, to be called at the
appropriate time (after PCH init, before DRAM init).
BUG=chrome-os-partner:20162.
TEST=Manual. Test on peppy board with non-zero SPD GPIOs, verify correct
SPD is selected.
Change-Id: I2554813e56a58c8c81456f1a53cc8ce9c2030a73
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58608
It might be that you want an early console in romstage before RAM is up, but
you can't or don't want to support the console all the way back in the
bootblock. By making the console in those two different environments
configurable seperately that becomes possible.
On the 5250 console output as early as the bootblock works, but on the 5420 it
only starts working in the ROM stage after clocks have been initialized.
BUG=chrome-os-partner:19420
TEST=Built and booted on pit with another change and an external tool, and was
able to get serial output. Built for snow.
BRANCH=None
Change-Id: Ie27ae7a7b22f336d23893618969efde4145fefd7
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/57725
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
If we clear the framebuffer and then flush it back to memory using cache
operations, the writes are going to be full cachelines at a time. If we
make it uncacheable first, the writes will be serialized writes of
whatever sized chunks memset uses, probably 4 bytes or less.
BUG=None
TEST=None
BRANCH=None
Change-Id: I59d6699fcea1c5ca4402ae6cf45df9c14878943a
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/55837
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
At one time it seemed to be necessary to disable and then re-enable the
MMU when setting the framebuffer to be uncache-able due to bugs in the
MMU management code. Since those bugs have been fixed, this is no longer
necessary.
BUG=None
TEST=None
BRANCH=None
Change-Id: I1fb2bd6e14777470456e9517d3efba24c3b170a0
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/55836
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
The code that allocated space for the framebuffer was adding space for a
vestigial color map which was never used. It was also passing around a
structure which was used to calculate a single value which was already
known when that structure was put together. Eliminate the extra space,
and pass the single value instead of the structure.
BUG=None
TEST=None
BRANCH=None
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: Ia21bcbfdd0007e9088c98c339aa031853a282cf5
Reviewed-on: https://gerrit.chromium.org/gerrit/55835
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
The code which figured out the rate of the input clock to a peripheral was
doing several things wrong. First, it was using the wrong values when
determing what the source of a clock was set to. Second, it was using the
wrong offset into that register to find the current source setting.
This change fixes the constants which select a clock source which get some
more things working, but doesn't attempt to fix the bit position table.
BUG=chrome-os-partner:19420
TEST=Built for pit with another change and an external tool, and was able to
receive serial output.
BRANCH=None
Change-Id: Ia2cea7ce8ee2c8ae721e09069bcf9711b1d30aec
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/57726
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Not all ARM systems need "BL1", and the layout of BL* and bootblock may be
different (ex, Exynos 5250 may use a new BL1 with variable length checksum
header).
To support that better, define the real base address (and ROM offset) of boot
block, and then we can post-processing ROM image file by filling data / checksum
and any other information.
BUG=none
TEST=manual: emerge-daisy chromeos-coreboot-snow;
emerge-peach_pit chromeos-coreboot-peach_pit
BRANCH=none
Change-Id: I9b3ee083c2edac64a653d5d7dffc123d252878d7
Reviewed-on: https://gerrit.chromium.org/gerrit/58342
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
On x86 there is a 16-byte alignment requirement for the
addresses containing the CPU microcode. The cbfs files
containing the microcode are used in memory-mapped fashion
when loading new mircocode. Therefore, the data payload's
address/offset of a cbfs file in flash dictates the resulting
alignment. Fix this by processing the CPU microcode cbfs
file separately as it uses $(CBFSTOOL) to find the proper
location within the provided rom image.
BUG=chrome-os-partner:20100
BRANCH=None
TEST=Manually inspected cbfs layout:
CBFS @ Offset 0x00700000 into 0x00800000 ROM size
[0xfff00000] cmos_layout.bin type cmos layout (0x1aa) @ 0xfff00028,
0x48c (1164) bytes
[0xfff004c0] pci8086,0406.rom type optionrom (0x30) @ 0xfff004f8,
0x10000 (65536) bytes
[0xfff10500] cpu_microcode_blob.bin type microcode (0x53) @ 0xfff10560,
0x9c40 (40000) bytes
[0xfff1a1c0] config type raw (0x50) @ 0xfff1a1e8, 0x157f (5503) bytes
[0xfff1b780] fallback/vboot type stage (0x10) @ 0xfff1b7a8, 0x3ad3
(15059) bytes
[0xfff1f280] (empty) type null (0xffffffff) @ 0xfff1f2a8, 0xcd8 (3288)
bytes
[0xfff1ff80] fallback/romstage type stage (0x10) @ 0xfff1ffe4, 0xa001
(40961) bytes
[0xfff2a000] fallback/coreboot_ram type stage (0x10) @ 0xfff2a038,
0x15373 (86899) bytes
[0xfff3f3c0] fallback/payload type payload (0x20) @ 0xfff3f3f8, 0xd00e
(53262) bytes
[0xfff4c440] u-boot.dtb type unknown (0xac) @ 0xfff4c468, 0x1e4b (7755)
bytes
[0xfff4e2c0] (empty) type null (0xffffffff) @ 0xfff4e2e8, 0x51cd8
(335064) bytes
[0xfff9ffc0] mrc.bin type mrc (0xab) @ 0xfffa0000, 0x2d8b8 (186552)
bytes
[0xfffcd8c0] (empty) type null (0xffffffff) @ 0xfffcd8e8, 0x1e6d8
(124632) bytes
[0xfffebfc0] spd.bin type mrc (0xab) @ 0xfffec000, 0x200 (512) bytes
[0xfffec200] (empty) type null (0xffffffff) @ 0xfffec228, 0x13418
(78872) bytes
Change-Id: Icc676a1c76c368d77e48cf573c6f846301da42a2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/58238
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Change every "boot loader 1" to be same file name in different folders.
BUG=none
TEST=manual: emerge-daisy chromeos-firmware-snow
BRANCH=none
Change-Id: Ie709b74b3bd3340f2cdc7b5685300102340bb399
Reviewed-on: https://gerrit.chromium.org/gerrit/58125
Tested-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Hung-Te Lin <hungte@chromium.org>
Now that we are executing VbInit() in coreboot we can end up
in a situation where the recovery reason is consumed during
VbInit (end of romstage) and then the EC is rebooted to RO
during ramstage EC init, thereby losing the recovery reason.
Two possiblities are to remove the EC check+reboot from ramstage
and let it happen in depthcharge. This however means that the
system has to boot all the way into depthcharge and then reboot
the EC and the system again.
Instead if we do a check in romstage before VbInit() is called
then we can reboot the EC into RO early and avoid booting all
the way to depthcharge first.
This change adds a ramstage version the EC init function and
calls it from the shared romstage code immediately after the
PCH decode windows are setup.
BUG=chrome-os-partner:19928
BRANCH=none
TEST=manual: enter recovery with crossystem recovery_request=193
Change-Id: Ic927c69a95a2114e29c343f0dcc28374266db394
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57470
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When an INIT# is delivered to the CPU the CPU starts
executing from the reset vector. However, the internal state
is maintained. Therefore, check for such a condition and
reset the system.
BUG=chrome-os-partner:19355
BRANCH=None
TEST=Issues 'apreset warm' on the EC console. INIT# is sent and
CPU notices it's not a clean reset and forces one. No hangs.
Change-Id: I71229e0e5015ba8c60f5989c533268604ecc1ecc
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57111
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
There were assumptions being made in the haswell
MP and SMM code which assumed the APIC id space
was 1:1 w.r.t. cpu number. When hyperthreading is
disabled the APIC ids of the logical processors
are all even. That means the APIC id space is sparse.
Handle this situation.
BUG=chrome-os-partner:19699
BRANCH=None
TEST=Used HT disabled part on WTM2. No more spontaneous reboots.
Change-Id: Ia4e3aa7456092e0ac0ea0ef16f10ba638a3e6dbe
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56824
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The new code is stolen from U-Boot with little or no understanding of how it
works.
BUG=chrome-os-partner:16132
TEST=Built for pit. Verified that boot progressed past clock initialization.
BRANCH=None
Change-Id: I3f826e799529adee89898015af9e3f3a5114b7f5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/55570
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
This function had been declared in a public header file, but was marked
static when actually defined.
BUG=chrome-os-partner:16132
TEST=Built for pit.
BRANCH=None
Change-Id: I7cc9e583c20e54c926b805fcc49b06b629c8a508
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/55569
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
