When libpayload header files are included in the payload itself, it's possible
that the payloads config settings will conflict with the ones in libpayload.
It's also possible for the libpayload config settings to conflict with the
payloads. To avoid that, the libpayload config settings have _LP_ (for
libpayload) added to them. The symbols themselves as defined in the Config.in files
are still the same, but the prefix added to them is now CONFIG_LP_ instead of just
CONFIG_.
BUG=chrome-os-partner:19420
TEST=Built and booted on pit. Built libpayload and depthcharge on all
supported platforms.
BRANCH=None
Change-Id: Ib8a46d202e7880afdeac7924d69a949bfbcc5f97
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65303
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Empirical testing shows that 0x5 is the optimal setting for DTLE DATA /
EDGE on Peppy.
BUG=chrome-os-partner:21712.
TEST=Manual. Set DTLE configuration on Peppy, read back registers to
verify.
BRANCH=FalcoPeppy.
Change-Id: I273a3a68be97b3eb7c2ee2071e5de1ef7bf7f2d9
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65717
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Allow DTLE DATA / EDGE registers to be configured in board-specific
devicetree.
BUG=chrome-os-partner:21712.
TEST=Manual. Set DTLE configuration on Peppy, read back registers to
verify.
BRANCH=FalcoPeppy.
Change-Id: I82307d08c9cf73461db3ac7fb875a4fe70d6f9ea
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65716
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Some mainboards will need to have this set.
BUG=none
BRANCH=none
TEST=Boot coreboot on Falco with no visible changes
(Similar change to coreboot required)
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I4732a9af822a60b5050d03d2ac4bb7cbd6c723d0
Reviewed-on: https://gerrit.chromium.org/gerrit/65722
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
The coreboot and ACPI code that clears USB3 PORTSC change status
bits was not properly preserving the state of the PED (port enabled
or disabled) status bit, and it could write 0 back to this field
which would disable the port.
Additionally add back the code that resets disconnected USB3 ports
on the way into suspend (as stated in the BWG) but take care to
clear the PME status bit so we don't immediately wake.
BUG=chrome-os-partner:21876
BRANCH=falco,peppy
TEST=manual: suspend/resume with USB3 devices
1) suspend with no devices, plug in while suspended, then resume
and verify that the devices are detected
2) suspend with USB3 devices inserted, then suspend and resume
and verify that the devices are detected
3) suspend with USB3 devices inserted, then remove the devices
while suspended, resume and ensure they can be detected again
when inserted after resume
Change-Id: Ic7e8d375dfe645cf0dc1f041c3a3d09d0ead1a51
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65733
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Now that the rtd2132 device has the full settings the
panel timings need to be implemented. Sadly, the Tx timings
in the rtd2132 aren't 1:1 with the panel's Tx timings. Below
is the table equivalent:
RTD2132 | Falco Panel
--------+------------
T1 | T2
--------+------------
T2 | T8+T10+T12
--------+------------
T3 | T14
--------+------------
T4 | T15
--------+------------
T5 | T9+T11+T13
--------+------------
T6 | T3
--------+------------
T7 | T4
--------+------------
BUG=chrome-os-partner:20924
BRANCH=falco
TEST=Built and booted
Change-Id: I10a3ad475d6b9485a707eb49e31afd197fc8d24d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65858
Reviewed-by: Stefan Reinauer <reinauer@google.com>
It has been disseminated that the RTD2132 chip
needs to be fully programmed for settings to take affect.
Most of the settings are note documented very well and
present themselves as magic values. Also, the wait time
for starting the sequence needs to be bumped from 2ms to 60ms.
Lastly, expose all the known settings through devicetree.
BUG=chrome-os-partner:20924
BRANCH=falco
TEST=Built and booted.
Change-Id: I9eeea9c4a13ec20b8ce1c5297e43c4dd793d90e5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65857
Reviewed-by: Stefan Reinauer <reinauer@google.com>
This ensures that the LCD FETs are off before we do graphics init.
FIXME: The location of the code is sub-optimal and should probably be
done in romstage, but there are __PRE_RAM__ considerations to take
into account.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted, things are still broken
Change-Id: I0844030d0a0e51eee1d29f1762f0b495777268df
Reviewed-on: https://gerrit.chromium.org/gerrit/64305
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Assign correct parent PLL's for the following clocks:
ACLK_400_WCORE (MPLL->CPLL) (400 -> 333MHz)
PCLK_200_FSYS (MPLL->DPLL) (200 -> 200MHz)
MUX_ACLK_100_NOC_SEL (MPLL -> DPLL) (100 -> 100MHz)
ACLK_266 (DPLL->MPLL) (300 -> 266MHz)
ACLK_200_DISP1(MPLL->DPLL) (200 -> 200MHz)
ACLK_400_MSCL(MPLL->CPLL) (400 -> 333MHz)
ACLK_66 (MPLL->CPLL) (66.666 -> 66.6MHz)
MUX_ACLK_400_DISP1_SEL (CPLL->DPLL) (666 -> 300MHz)
MUX_MPHY_REFCLK (MPLL->OSC)
MUX_UNIPRO (MPLL->OSC)
MUX_MIPI1 (EPLL->OSC)
MUX_DP1_EXT_VID (EPLL->OSC)
MUX_FIMD1_OPT (EPLL->OSC)
MUX_IPLL(IPLL->OSC)
This also corrects the clock dividers for few of the clocks,
as the clock parent changes affect the final frequency of the
clocks.
This is ported from: https://gerrit.chromium.org/gerrit/#/c/62437/
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted on pit
Change-Id: Ie833c01913d0961a6190446bd573511de8dee5f8
Reviewed-on: https://gerrit.chromium.org/gerrit/65620
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
This reads the clock select field for MUX_ACLK_66_SEL in the
CLK_SRC_TOP1 register in order to obtain the source clock rate
for I2C peripherals. Before we were always assuming that the source
was the MPLL.
Unfortunately not all fields in the CLK_SRC_TOPn registers are
enumerated the same with regard to clock select. So this is just
a one-off for now.
This is basically ported from https://gerrit.chromium.org/gerrit/#/c/62443.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted on Pit
Change-Id: I9fa85194ae1a1fadab79695f059efdc2e2f1f75f
Reviewed-on: https://gerrit.chromium.org/gerrit/65611
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
This is causing hangs in depthcharge (again?) so for now
turn that port off so the resulting coreboot images are
at least useful.
BUG=none
BRANCH=none
TEST=boot on wtm2 and press Ctrl+D at developer screen with USB keyboard
Change-Id: I32c7774a95b0020b97105e0fa42c21ccb617c718
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65615
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We set up L2 cache early in romstage now so the old
function is now redundant.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted on pit, cat /proc/cmdline shows 4 A15 cores
Change-Id: Icec93810ddd7feb48286d4b600cb2d58af38b7ef
Reviewed-on: https://gerrit.chromium.org/gerrit/65428
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Increase SPLL to 400MHz from 300MHz as we set SPLL as the
switching parent for ARM and KFC. This value is as per
recommendation of the hardware team.
This is ported from https://gerrit.chromium.org/gerrit/62618
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted on Pit
Change-Id: I8a5a5b957083b0b1f3e3e318fe5753cf7ae19223
Reviewed-on: https://gerrit.chromium.org/gerrit/65432
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
This re-factors clock_get_periph_rate() to be a simpler and also
make a few corrections along the way. To summarize:
- clk_bit_info is no longer used. It had numerous errors and was
really painful anyway since it was just a bunch of opaque magic
numbers that made bugs non-obvious.
- Clock source bitfields for peripherals handled in the switch
statement are 3 bits, not 4. Some divider values are 3 bits,
some are 4. The earlier code always assumed 4 bits for both
which included reserved bits in many cases.
- UART source clock and divider shift values were wrong.
- PWM clock divider was being read from the wrong register.
- SPI3 divider value was being read from the wrong register.
- There was a really confusing calculation for SDMMC0 and SDMMC2
clock rates, but it was never actually used since the switch
statement never handled PERIPH_ID_SDMMC{0,2} and would thus
return if they were ever passed into this function.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted on pit
Change-Id: I0a03a64d8b42fbe83dbf377292597ce681b22f4b
Reviewed-on: https://gerrit.chromium.org/gerrit/65284
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
This adds a helper function to translate between peripheral clock
select fields in clock source registers and PLLs. Some of this was
already done to handle a few special cases, this generalizes the
earlier work so that follow-up patches can do further clean-up.
Unfortunately, the PLLs represented by clock select fields in
various modules are not uniformly ordered. So for now we focus on
peripheral clock sources only.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted on pit
Change-Id: Id58a3e488650d09e6a35c22d5394fcbf0ee9ddff
Reviewed-on: https://gerrit.chromium.org/gerrit/65283
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
This patch adds CPLL and DPLL to the known list of PLLs.
This is ported from https://gerrit.chromium.org/gerrit/#/c/62617/
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted pit
Change-Id: I2f2614e44cd9c98d98b8db9347f29de21703d1af
Reviewed-on: https://gerrit.chromium.org/gerrit/65282
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
The SMI handler code was setting S3 wake events when going
into S5 and enabling a key press to wake the system.
BUG=chrome-os-partner:21025
BRANCH=falco,peppy
TEST=manual: power off and try to wake with key press
Change-Id: I6413ef1341e0149187df9f4f7e0c314d4c9e9c6e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65323
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch matches the User Manual Table 7-2 about the PMS value for
CPLL. This doesn't change the PLL frequency (before and after both make
666MHz) but this is the suggested PMSK values for obtaining 666.
(Suggested as per user manual).
This is ported from https://gerrit.chromium.org/gerrit/#/c/62438/
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted on Pit
Change-Id: Ia33e1971ab88da761000d443792560476514626b
Reviewed-on: https://gerrit.chromium.org/gerrit/65281
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
If the firwmare is flashed and the MRC cache is blown away
then it is not possible to resume.
Right now this can be inferred from the event log but it can
be made very clear by adding a unique post code for this event.
BUG=none
BRANCH=falco
TEST=manual:
1) boot falco
2) flash firmware
3) suspend and then resume
4) check for post code 0xef in log
0 | 2013-08-08 16:27:47 | Log area cleared | 4096
1 | 2013-08-08 16:27:47 | ACPI Enter | S3
2 | 2013-08-08 16:27:55 | System boot | 48
3 | 2013-08-08 16:27:55 | Last post code in previous boot | 0xef | Resume Failure
4 | 2013-08-08 16:27:55 | System Reset
5 | 2013-08-08 16:27:55 | ACPI Wake | S5
Change-Id: I7602d9eef85d3b764781990249ae32b84fe84134
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65259
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The previous implementation was overly complicated, and when used in the
timestamp implementation produced some weird and broken results.
BUG=chrome-os-partner:19420
TEST=Built and booted on pit. Used cbmem to check the timestamps and saw that
they were now monotonically ascending and within reasonable bounds.
BRANCH=None
Change-Id: I3048028ddea0657b01b0c94f312764b38d1397e4
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65302
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Otherwise there's no good way to create an absolute timer structure without
fiddling with its internal structure or assuming a zero initialized structure
has a value of zero.
BUG=chrome-os-partner:19420
TEST=Used in a new monotonic implementation on pit.
BRANCH=None
Change-Id: Iffe3b6b25ed7963fcfb66f749c531ea445ea4aeb
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65301
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
If the cbmem console buffer isn't zero filled before it's used, there won't be
a terminator at the end. We need to put one at the cursor position manually.
BUG=chrome-os-partner:19420
TEST=Booted and ran cbmem -c on pit. No longer saw lots of garbage printed
after the actual console output.
BRANCH=None
Change-Id: I69870c2b24b67ce3cbcd402b62f3574acb4c2a8f
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65300
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Configure the pins for the UART unconditionally in the mainboard code (when we
know which UART to configure) instead of in the UART driver. This also means
the UART will work if later software wants to use it without setting up the
pins.
BUG=chrome-os-partner:19420
TEST=Built and booted on pit with the serial turned off and some serial init
in the kernel decompression stub fixed.
BRANCH=None
Change-Id: Icab5755e4f935f52d44b9cb3b43d1cb62acce08f
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65299
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
This patch implements the basic infrastructure required to use the USB
A-A firmware upload feature on Exynos5 processors with Coreboot. It will
require a corresponding host-side script that activates the feature and
uploads the correct image parts in the correct order to harcoded target
addresses, as described in the comments of alternate_cbfs.c.
Also fixes a bug in the Google Snow mainboard where it would not
correctly initialize the pinmux configuration for the SPI flash bus.
During a normal SPI boot the IROM would already do that for you, but
when booting from USB you have to do it yourself.
BUG=None
TEST=Manual
Change-Id: I40a39f8f5d1d70b58dbf258015c1653a27097d67
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/64875
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
The SMP on Exynos 5420 requires setting a special page and entry wrappers in
firmware side (SRAM) so kernel can start cores (and to switch clusters).
BUG=chrome-os-partner:19420
TEST=built on pit and see 8 CPUs started.
Change-Id: I77ca98bb6cff5b13e95dd29228e4536302f0aee9
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/64770
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
These can typically be set in the devicetree but we need a way to
override those values with a Kconfig setting so as not to expose
the Vendor ID before the product has launched.
BUG=chrome-os-partner:21614
BRANCH=falco,peppy
TEST=emerge-falco chromeos-coreboot-falco
Change-Id: Ib382e6d9359d24b128c693a657ffde52604efad3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65310
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
BUG=chrome-os-partner:21535
BRANCH=falco
TEST=manual: Boot on falco and look in /sys/firmware/log for
the string "PCIe Root Port 1 ASPM is enabled"
Change-Id: Ie2111e4bb70411aa697dc63c0c11f13fbe66c8d8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65315
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The PCIe root port has ASPM settings/workarounds that are only applied
based on the value of an undocumented bit in PCI config register 0x32C.
If that bit is not set for some reason then the settings are not applied.
This devicetree config option will force the ASPM settings for each port
based on the bit map.
BUG=chrome-os-partner:21535
BRANCH=falco,peppy
TEST=emerge-falco chromeos-coreboot-falco
Change-Id: I40b08ca9a0ef52742609bac72fb821454a373799
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65314
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The default ME output is quite verbose and not all that useful
unless you are actively debugging the ME and then you can enable
the CONFIG_DEBUG_INTEL_ME option.
This commit silences the firmware capabilities and the MBP output.
BUG=chrome-os-partner:21775
BRANCH=falco
TEST=emerge-falco chromeos-coreboot-falco
Change-Id: I2b8abcb34ae0d00d9a38d029979e84ee0d0ca287
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65252
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CLKOUT for PCIE ports 1-5 and CLKOUT_XDP are not used
and can be disabled.
BUG=chrome-os-partner:21775
BRANCH=falco
TEST=manual:
I couldn't test this directly without a scope so instead I
used a modified commit that also disabled PCIe Port 0 and
saw that that correctly disabled the WLAN port.
Change-Id: I0f996e90f0ae42780de3a0c8dc5db00ec600748b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65251
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This message allows unused clocks to be disabled based on a
devicetree setting in each mainboard.
BUG=chrome-os-partner:21775
BRANCH=falco,peppy
TEST=emerge-falco chromeos-coreboot-falco
Change-Id: Ib1988cab3748490cf24028752562c64ccbce2054
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65250
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The original ME code was assuming that the only type of messages
it would send were MKHI type and so it had some embedded checks
for that header and that type of message.
In order to support ICC messages this needs to change to handle
different header types, so now the header will be sent first
and then the data will follow, rather than the two both being
sent in the same low-level function.
This change has no real affect on the system, subsequent commit
will add new ICC messages.
BUG=chrome-os-partner:21775
BRANCH=falco,peppy
TEST=manual: compile and boot on falco with CONFIG_INTEL_ME_DEBUG
enabled to ensure the MEI transactions are successful.
Change-Id: I52848581e49b88c0a79e8bb6bda2a179419808a3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65249
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The end of the _PS0 method that is supposed to transition the
XHCI device to D0 state is instead putting it in D3 state.
This triggers a PME_B0 GPE which causes a Notify to the XHCI
ACPI Device in the kernel and that increments the wakeup counter
and causes aborted suspends.
Instead if we just leave the device in D0 where it should be
after executing this function then the PME_B0 is not generated
and the kernel does not see a wakeup on XHCI.
Similarly I changed the _PS3 method to always put the device in
D3 at the end of the method, rather than depending on the state
to be D3 at the start.
BUG=chrome-os-partner:21663
BRANCH=falco,peppy
TEST=manual: tested on falco
Before this change the kernel would see the following sequence
when trying to suspend when the XHCI controller is in D3cold:
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff88017802bf28)
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [XHCI] (Device) Value 0x02 (Device Wake) Node ffff88017802bc30
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [EHCI] (Device) Value 0x02 (Device Wake) Node ffff88017802b8e8
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [HDEF] (Device) Value 0x02 (Device Wake) Node ffff88017802b1b8
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
kernel: xhci_hcd 0000:00:14.0: PME# disabled
kernel: xhci_hcd 0000:00:14.0: enabling bus mastering
kernel: xhci_hcd 0000:00:14.0: setting latency timer to 64
kernel: PM: Wakeup pending, aborting suspend
kernel: last active wakeup source: 0000:00:14.0
Now it does not get a notification (due to PME_B0) when going to D0
on the way into suspend. XHCI goes from D3cold to D0 (in order to
be able to read mmio) and then back to D3hot before suspend.
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff88017802bf28)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
kernel: xhci_hcd 0000:00:14.0: PME# disabled
kernel: xhci_hcd 0000:00:14.0: enabling bus mastering
kernel: xhci_hcd 0000:00:14.0: setting latency timer to 64
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._S3D] (Node ffff88017802c000)
kernel: xhci_hcd 0000:00:14.0: PME# enabled
kernel: xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS3] (Node ffff88017802bf50)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D3hot
Change-Id: Id5cd28eede2b27d97640047feb17349ae4ab79b7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65236
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The test on official ChromeOS firmware bitmaps will be very blurry if
the screen resolution is too low (current value, 0x114 = 800x600).
(Port of gerrit-int falco change: I45bf72668a1e2d90a922964a20f7d9b9fcbdd6d0)
BUG=chrome-os-partner:21773.
TEST=emerge-peppy chromeos-coreboot-peppy.
BRANCH=FalcoPeppy.
Change-Id: Id870dc6829055313a71052b6f49a4c0330defc44
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65313
Reviewed-by: Dave Parker <dparker@chromium.org>
The ACTLR provides implementation defined configuration and control options for
the processor.
BUG=none
TEST=emerge-peach_pit chromeos-coreboot-peach_pit # success.
BRANCH=none
Change-Id: I74df1ed7887eb3f16a1b8297db998ec2f8b18311
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65107
Commit-Queue: Gabe Black <gabeblack@chromium.org>
The existing GPIO config routines for SDMMC0-2 are over-generalized
and somewhat confusing as a result. It would work nicely if all SDMMC
ports were configured in the same fashion, but there are a few
exceptions.
For example, the inner function runs differently if we're using 8 bits
of data instead of 4, so a big chunk is skipped for SDMMC2. SDMMC0
requires SD_0_CDn to be an output rather than alternate function and
must have a value set.
This patch trades some verbosity for simplicy. Now the SDMMC GPIO
configuration a straight-forward sequence of GPIO operations
without any exceptions.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted Pit (using eMMC)
Change-Id: If75075b24c6588c4c1b3be3fb9b1aa95e2fac2d1
Reviewed-on: https://gerrit.chromium.org/gerrit/65248
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
On Exynos5420 the MMC channel 0 is connected to eMMC
Which does not have a card detection pin. Also this pin
is connected as VDDEN to PMIC.
This is ported from https://gerrit.chromium.org/gerrit/#/c/60732/
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted on pit
Change-Id: I19048d22b7dd00df1716b6b5b332a7eb70fe0836
Reviewed-on: https://gerrit.chromium.org/gerrit/65247
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
To configure multi-processors, we need the intrinsic functions to get core ID,
put core into idle state, and to wake up cores.
BUG=none
TEST=emerge-peach_pit chromeos-coreboot-peach_pit # success.
BRANCH=none
Change-Id: I87a62dab6efd6c8bb0c8e46373da7c7eb7b16b35
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65112
Since system clock and console initialization now happen after power
setup, we cannot print error messages in setup_power(). This patch
re-factors the code a little bit to save the status of setup_power()
so that if we get an error during setup_power() we will wait until
we can actually print something before dying.
BUG=none
BRANCH=none
TEST=build and booted on pit
Change-Id: Id7ff477224b104b3c7e221c1d2df460ca9125f3b
Reviewed-on: https://gerrit.chromium.org/gerrit/65009
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
This initializes the APLL at 1800MHz.
BUG=none
BRANCH=none
TEST=built and booted on Pit
Change-Id: I366bf4e75510847ab93d9c9f214a49c731cca08a
Reviewed-on: https://gerrit.chromium.org/gerrit/64745
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Switch ARM clock source when changing the APLL frequency to avoid
stability issues.
This is ported from https://gerrit.chromium.org/gerrit/#/c/64189/5
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted on pit and snow
Change-Id: I923107555e6d3287b3694cbf9e4bb548d3e5f4a8
Reviewed-on: https://gerrit.chromium.org/gerrit/64838
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
This patch does the following for the A15 cores:
- Disable clean/evict push to external
- Enable hazard detect timout
- Prevent gating the L2 logic clock
This is ported from https://gerrit.chromium.org/gerrit/#/c/60154
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=built and booted on Pit, seems as stable as before...
Change-Id: I7ac9f40acecfa7daee6fb81772676bf5119d0536
Reviewed-on: https://gerrit.chromium.org/gerrit/64862
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
BUG=chrome-os-partner:19420
TEST=Built and booted on snow. Beeped in depthcharge through the i2s0 bus.
BRANCH=None
Change-Id: I6729a139091b40d8fd9ba2aa7a8c4e14216d95c5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64879
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
The hexdump function was added to libpayload recently, but its source file was
never added to the Makefile so it wasn't compiled or linked in.
BUG=None
TEST=Built and booted into a firmware that called hexdump in the payload.
Before this change the build would fail because the hexdump symbol wasn't
defined.
BRANCH=None
Change-Id: Ic3c12a5b8a6ea631b83c10a6e4210544ff00b5bf
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64878
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
This bus is hooked up on snow and, as it's the only bus hooked up on some
other boards, having it available in firmware to test is handy.
BUG=chrome-os-partner:19420
TEST=Built and booted on snow and heard a beep.
BRANCH=None
Change-Id: Icb48b9af4a67d382bd6fbce1e4c6a320d811d365
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64877
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
This moves the call to setup_power() before system_clock_init().
This causes the PMIC to set up the voltage rails earlier so that
the CPU clock can be set up at a faster rate (in the follow-up
patch). After system clock init, we re-initialize the PMIC's I2C
bus since the input clock rate will have changed.
BUG=none
BRANCH=none
TEST=built and booted on Pit
Change-Id: Ieb828ac25daad7ee95bfa4823aaaf161028c9c92
Reviewed-on: https://gerrit.chromium.org/gerrit/64744
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
This adds inline wrappers to read the L2 cache auxiliary control
register (L2ACTLR).
Signed-off-by: David Hendricks <dhendrix@chromium.org>
BUG=none
BRANCH=none
TEST=it builds (tested more thoroughly w/ follow-up patches)
Change-Id: Iec603d7c738426232f7ce3a4a474d01c85fa3f2f
Reviewed-on: https://gerrit.chromium.org/gerrit/64861
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
BUG=None
TEST=Built and booted on pit.
BRANCH=None
Change-Id: I128e3ecc3773fe7c28616e93ef60b48c5862f302
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/64839
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
