The SystemAgent contains a mini-hd audio controller at PCI 0:3.0
which uses the same verb table init sequence as the southbridge.
In order to avoid two copies of the verb table loading code I
separated out the HDA verb table functions into a file that can
be re-used and then added a minihd driver to the haswell northbridge.
The minihd verb table is the same across devices so it can live
within the minihd driver rather than needing to be specified in
each separate mainboard.
I also fixed up the driver for lynxpoint HDA by following the
reference code.
BUG=chrome-os-partner:19993
BRANCH=none
TEST=manual: boot into linux and check for mini-hd
Without HDMI cable plugged in driver does not find any codec,
and it does not seem to re-probe when HDMI is connected. We may
be missing kernel patches for this.
hda-intel 0000:00:03.0: no codecs found!
With a basic kernel patch to add 0x0a0c device ID to HDA driver
and with HDMI cable connected it is much happier:
snd_hda_intel 0000:00:03.0: irq 60 for MSI/MSI-X
input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
snd_hda_intel 0000:00:1b.0: irq 61 for MSI/MSI-X
input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11
Change-Id: Ifa587984be4fc2801704a0368b9cdf8379c2450e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59336
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
- Add a new USB location field
- Add a new "ddr_refresh_2x" field, enabled on Falco only
- Fix copy+paste bug in baskingridge
BUG=chrome-os-partner:19869
BRANCH=none
CQ-DEPEND=CL:*39053
TEST=manual: test to ensure refresh rate 2x can be enabled
Checked that tREFI is halved during memory setup in the memory
training log:
tREFImin = 6240 << DEFAULT
C(0).tREFI = 0xc30 << MODIFIED (=3120)
C(0).tREFI = 0xc30 << MODIFIED (=3120)
Also ensure that the SD card is detected properly again.
Change-Id: Ie3a82c08df06ada9af56282b5255caefa56487f2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57349
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It's possible that the TOUUD can be set to less than
4GiB. When that is the case the size_k variable is
an extremely large value. Instead ensure TOUUD is greater
than 4GiB before adding said resources.
BUG=None
BRANCH=None
TEST=Built and booted.
Change-Id: I456633d6210824e60665281538300fd15656b86d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57329
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The haswell i915 kernel driver apparently expects the VBIOS
to set a few specific registers. This sequence is enough to
make the driver happy without executing the VBIOS.
This also makes graphics work after suspend/resume.
BUG=chrome-os-partner:19638
BRANCH=none
TEST=manual: boot normal mode on slippy
Change-Id: I34937d55ffff8a9445442e6e6ca1bfc49869da63
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56806
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Update and use the new pei_data data structure. Now that the
reference code is fixed it's possible to properly disable/enable
the USB2 and USB3 ports correctly.
BUG=None
BRANCH=None
TEST=emerge slippy. All USB connections available to me still work. Both
USB3 and USB2. Other boards assumed to work.
Change-Id: I075c646e7574be354420b6e59507e8917a97d0f0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56594
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
In case we are going to use this in future designs.
BUG=none
TEST=none
BRANCH=none
Change-Id: I750addf10e4fe6f8240f8c8262253f8af7027e29
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/55844
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This was changed to 0x80000000 in SA BWG 1.5.0.
BUG=chrome-os-partner:16862
BRANCH=none
TEST=build and boot on wtm2
Change-Id: Ic6773f45057f3eb93b2d93ee543e3db77fccf805
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50852
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
... and drop the wrapper on ARMv7
BUG=none
TEST=boot tested on snow
BRANCH=none
Change-Id: Ib2b4315b664292653f8cb898fc5633fce421deca
Reviewed-on: https://gerrit.chromium.org/gerrit/50728
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Commit "romcc: Don't fail on function prototypes" (11a7db3b) [1]
made romcc not choke on function prototypes anymore. This
allows us to get rid of a lot of ifdefs guarding __ROMCC__ .
[1] http://review.coreboot.org/2424
BUG=none
TEST=boot tested on Link
BRANCH=none
Change-Id: Ib1be3b294e5b49f5101f2e02ee1473809109c8ac
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3216
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/50723
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
This option has not been enabled on any board and was considered
obsolete last time it was touched. If we need the functionality,
let's fix this in a generic way instead of a K8 specific way.
This was mostly a speedup hack back in the day.
BUG=none
TEST=not needed (inactive option dropped)
BRANCH=none
Change-Id: Ib1ca248c56a7f6e9d0c986c35d131d5f444de0d8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3211
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/50722
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
it has been unused since 9 years or so, hence drop it.
BRANCH=none
BUG=none
TEST=boot tested on snow
Change-Id: I0706feb7b3f2ada8ecb92176a94f6a8df53eaaa1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3212
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/50720
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Instead of using the local apic timer for udelay() use the tsc.
That way SMM, romstage, and ramstage all use the same delay
functionality.
BUG=None
BRANCH=None
TEST=Compiled and booted
Change-Id: Iac35eb02b424b54e490b4fdaa2fc74f35066db27
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50452
Reviewed-by: Stefan Reinauer <reinauer@google.com>
The cbmem_post_handling() function was implemented by 2
chipsets in order to save memory configuration in flash. Convert
both of these chipsets to use the boot state machine callbacks
to perform the saving of the memory configuration.
Change-Id: Ic086cae17491a20d2e81aa1c7922bd821aacb00b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49745
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
We've got enough of a handle on this to realize some things:
drm_dp_helper.h is by design device and architecture independent
i915.h is common to most intel graphics chipsets going back several years
i915_reg.h is as well
Move these files to src/include/device, and adjust the .c files accordingly.
Change-Id: Iee680a3513a957214294c19167d9487aaf2f4d97
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49184
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
This code is the initial version of FUI for haswell and wtm2.
The code is simplified from before in many ways. I've gotten rid of
the opcode table, because it obscured meaning and I don't think it is
needed any more. Register sets, mainly used for reset, are just lines
of code -- not many of them. There are a bunch of not-yet-documented
registers here; the VBIOS seemed to think they were necessary and
testing shows they seem to be right.
As a bit of added paranoia, we always include the VBIOS code as our
emergency recovery path. You have to run it now anyways, so this is no
regression from our current situation; and, if all goes well, in a
week (or so), you'll never have to run it again, but like the Force
and nose hair, it will be with you always.
The code can return in three ways. The first, best way is success:
panel is up and the VBIOS need not run. The second mode is that we
tried to light up the panel but could not, for some reason, but will
return with the panel partly up. In this case, it's ok not to power
cycle the panel. The third, worst case, which will NEVER happen, ha
ha, is that we have to turn the panel off and wait the required 600ms
for it to cycle. Life sucks sometimes. This failure mode is in the
'hang on we're going to fix it' category now that we have ramstage in
RW.
The Big Goal here is to create something other coreboot ports can use
as well. The guys doing the x60 report that the link FUI works,
without too many mods, on that chipset, so it seems Intel is keeping
things from changing too much over time.
Also, again, please note: this and the next 3 versions will ALWAYS fail.
The goal is to verify the correctness of the recovery path.
The bizarre tab-space formatting in drm_dp_helper.h is from the original,
as in i915_reg.h
BUG=None
TEST=build and boot wtm2 and see that FUI failed in a way that VBIOS can
recover from
BRANCH=NONE
Change-Id: I6dfed46500b80c69967aa253a8f24556a5281dfc
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/48848
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
This lights up the display. We don't get graphics but we are missing the gttsetup
at this point, so that is no shock. The real shock is that anything works at all.
Change-Id: Iea998ce3784743a46c9c9c9e70f29a462bf9bd39
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48287
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
This was there since the beginning
commit d24d6993b6
Author: arch import user (historical) <svn@openbios.org>
Date: Wed Jul 6 17:06:46 2005 +0000
Revision: linuxbios@linuxbios.org--devel/freebios--devel--2.0--patch-26
Creator: Hamish Guthrie <hamish@prodigi.ch>
Added AMD GX1 northbridge and cs5530 Southbridge
but blindly copied from Intel 440 BX and is not used anywhere.
Thanks to Idwer Vollering for spotting this.
Change-Id: I38b3d3feb25966c3aa382994d323e59c3f3c9e6c
Reported-by: Idwer Vollering
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3020
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: build bot (Jenkins)
If ROM caching is selected the sandybridge chipset code will
will enable ROM caching after all other CPU threads are brought
up.
Change-Id: I3a57ba8753678146527ebf9547f5fbbd4f441f43
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3017
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The graphics memory can be accessed in a faster manner by
setting it to write-combing mode. Add an option to enable
write-combining for the graphics memory.
Change-Id: I7d37fd78906262aabef92c2b4f4cab0e3f7e4f6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2894
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The graphics memory can be accessed in a faster manner by
setting it to write-combing mode. Add an option to enable
write-combining for the graphics memory.
Change-Id: I797fcd9f0dfb074f9e45476773acbfe614eb4b0a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2893
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The old MTRR code had issues using too many variable
MTRRs depending on the physical address space layout dictated
by the device resources. This new implementation calculates
the default MTRR type by comparing the number of variable MTRRs
used for each type. This avoids the need for IORESOURE_UMA_FB
because in many of those situations setting the default type to WB
frees up the variable MTTRs to set that space to UC.
Additionally, it removes the need for IORESOURCE_IGNORE_MTRR
becuase the new mtrr uses the memrange library which does merging
of resources.
Lastly, the sandybridge gma has its speedup optimization removed
for the graphics memory by writing a pre-determined MTRR index.
That will be fixed in an upcoming patch once write-combining support
is added to the resources.
Slight differences from previous MTRR code:
- The number of reserved OS MTRRs is not a hard limit. It's now advisory
as PAT can be used by the OS to setup the regions to the caching
policy desired.
- The memory types are calculated once by the first CPU to run the code.
After that all other CPUs use that value.
- CONFIG_CACHE_ROM support was dropped. It will be added back in its own
change.
A pathological case that was previously fixed by changing vendor code
to adjust the IO hole location looked like the following:
MTRR: Physical address space:
0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
0x00000000000c0000 - 0x00000000ad800000 size 0xad740000 type 6
0x00000000ad800000 - 0x00000000d0000000 size 0x22800000 type 0
0x00000000d0000000 - 0x00000000e0000000 size 0x10000000 type 1
0x00000000e0000000 - 0x0000000100000000 size 0x20000000 type 0
0x0000000100000000 - 0x000000014f600000 size 0x4f600000 type 6
As noted by the output below it's impossible to accomodate those
ranges even with 10 variable MTRRS. However, because the code
can select WB as the default MTRR type it can be done in 6 MTRRs:
MTRR: default type WB/UC MTRR counts: 6/14.
MTRR: WB selected as default type.
MTRR: 0 base 0x00000000ad800000 mask 0x0000007fff800000 type 0
MTRR: 1 base 0x00000000ae000000 mask 0x0000007ffe000000 type 0
MTRR: 2 base 0x00000000b0000000 mask 0x0000007ff0000000 type 0
MTRR: 3 base 0x00000000c0000000 mask 0x0000007ff0000000 type 0
MTRR: 4 base 0x00000000d0000000 mask 0x0000007ff0000000 type 1
MTRR: 5 base 0x00000000e0000000 mask 0x0000007fe0000000 type 0
Change-Id: Idfcc78d9afef9d44c769a676716aae3ff2bd79de
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2889
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
mmio_resource() was previously being used for reserving
RAM from the OS by using IORESOURCE_IGNORE_MTRR atrribute.
Instead, be more explicit for those uses with
reserved_ram_resource(). bad_ram_resource() now calls
reserved_ram_resource(). Those resources are marked as cacheable
but reserved.
The sandybridge and haswell code were relying on the implementation
fo the MTRR algorithm's interaction for reserved regions. Instead
be explicit about what ranges are MMIO reserved and what are RAM
reserved.
Change-Id: I1e47026970fb37c0305e4d49a12c98b0cdd1abe5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2886
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Convert the existing haswell code to support reloctable ramstage
to use dynamic cbmem. This patch always selects DYNAMIC_CBMEM as
this option is a hard requirement for relocatable ramstage.
Aside from converting a few new API calls, a cbmem_top()
implementation is added which is defined to be at the begining of the
TSEG region. Also, use the dynamic cbmem library for allocating a
stack in ram for romstage after CAR is torn down.
Utilizing dynamic cbmem does mean that the cmem field in the gnvs
chromeos acpi table is now 0. Also, the memconsole driver in the kernel
won't be able to find the memconsole because the cbmem structure
changed.
Change-Id: I7cf98d15b97ad82abacfb36ec37b004ce4605c38
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2850
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Dynamic cbmem is now a requirement for relocatable ramstage.
This patch replaces the reserve_* fields in the romstage_handoff
structure by using the dynamic cbmem library.
The haswell code is not moved over in this commit, but it should be
safe because there is a hard requirement for DYNAMIC_CBMEM when using
a reloctable ramstage.
Change-Id: I59ab4552c3ae8c2c3982df458cd81a4a9b712cc2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2849
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This makes use of the new functions from pmutil.c that take
care of the differences between -H and -LP chipsets.
It also adds support for the LynxPoint-LP GPE0 register block
and the SMI/SCI routing differences.
The FADT is updated to report the new 256 byte GPE0 block on
wtm2/wtm2 boards which is too big for the 64bit X_GPE0 address
block so that part is zeroed to prevent IASL and the kernel
from complaining about a mismatch.
This was tested on WTM2. Unfortunately I am still unable to get an
SCI delivered from the EC but I suspect that is due to a magic
command needed to put the EC in ACPI mode. Instead I verified that
all of the power management and GPIO registers were set to expected
values.
I also tested transitions into S3 and S5 from both the kernel and
by pressing the power button at the developer mode screen and they
all function as expected.
Change-Id: Ice9e798ea5144db228349ce90540745c0780b20a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2816
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SMM region is available for multipurpose use before the SMM
handler is relocated. Provide a configurable sized region in the
TSEG for use before the SMM handler is relocated. This feature is
implemented by making the reserved size a Kconfig option. Also
make the IED region a Kconfig option as well. Lastly add some sanity
checking on the Kconfig options.
Change-Id: Idd7fccf925a8787146906ac766b7878845c75935
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2804
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that there is a way to disseminate the presence of s3 wake more
formally use that instead of hard coded pointers in memory and stashing
magic values in device registers. The northbridge code picks up the
field's presence in the romstage_handoff structure and sets up the
acpi_slp_type variable accordingly.
Change-Id: Ida786728ce2950bd64610a99b7ad4f1ca6917a99
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2799
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Provide the implemenation of cbmem_get_table_location() so that
cbmem can be initialized early in ramstage when CONFIG_EARLY_CBMEM_INIT
is enabled. The cbmem tables are located just below the TSEG region.
Change-Id: Ia160ac6aff583fc52bf403d047529aaa07088085
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2798
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is not needed in haswell.
Change-Id: I23817c2e01be33855f9d5a5e389e8ccb7954c0e2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2847
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change:
This is the initial step for moving the AMD F15 & HUDSON1,2,3
SPD-read callout out of the mainboard directories and into
the wrapper. The next step is to update the platforms to use
this routine in BiosCallouts.c and to delete the code from the
mainboard directories. The DIMM addresses should be moved into
devicetree.cb.
If there are significant differences or reasons that the mainboard
needs to override this code, it's perfectly reasonable to keep using
the version in the mainboard, but this allows us to remove duplicated
code and simplify the mainboard directories.
Notes:
This started by duplicating what was in Dinar, and was changed to
use the devicetree.cb structures. Significant cleanup and magic
number reduction was done as well.
It is intended that this file will not be included in ramstage as
the DIMM init is all done in romstage.
This is similar to what was done for Parmer/Thatcher in commit
7fb692bd - http://review.coreboot.org/#/c/2190/
Fam15tn: Move SPD read from mainboards into wrapper
Yes, it would make sense to split this into two separate files
and move the SMBus initialization and access into the southbridge
wrapper. Maybe that can come next.
Change-Id: I4e00ada288e1486cf30684403505e475f9093ec2
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2777
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The save_mrc_data() was previously called conditionally
in the raminit code. The save_mrc_data() function was called
in the non-S3 wake paths. However, the common romstage_common()
code was checking cbmem initialization things on s3 wake. Between
the two callers cbmem_initialize() was being called twice in the
non-s3 wake paths. Moreover, saving of the mrc data was not allowed
when CONFIG_EARLY_CBMEM_INIT wasn't enabled.
Therefore, move the save_mrc_data() to romstage_common. It already has
the knowledge of the wake path. Also remove the CONFIG_EARLY_CBMEM_INIT
requirement from save_mrc_data() as well as the call to cbmem_initialize().
Change-Id: I7f0e4d752c92d9d5eedb8fa56133ec190caf77da
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2756
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This structure is not used nor the variable being instantiated on the
stack. Remove them.
Change-Id: If3abe2dd77104eff49665dd33570b07179bf34f5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2753
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It was found that the Haswell reference code was smashing through the
stack into the reference code's heap implementation. The reason for this
is because our current CAR allocation is too small. Moreover there are
quite a few things to coordinate between 2 code bases to get correct.
This commit separates the CAR into 2 parts:
1. MRC CAR usage.
2. Coreboot CAR usage.
Pointers from one region can be passed between the 2 modules, but one
should not be able to affect the others as checking has been put into
place in both modules.
The CAR size has effectively been doubled from 0x20000 (128 KiB) to
0x40000 (256KiB). Not all of that increase was needed, but enforcing
a power of 2 size only utilizes 1 MTRR.
Old CAR layout with a single contiguous stack with the region starting
at CONFIG_DCACHE_RAM_BASE:
+---------------------------------------+ Offset CONFIG_DCACHE_RAM_SIZE
| MRC global variables |
| CONFIG_DCACHE_RAM_MRC_VAR_SIZE bytes |
+---------------------------------------+
| ROM stage stack |
| |
| |
+---------------------------------------+
| MRC Heap 30000 bytes |
+---------------------------------------+
| ROM stage console |
| CONFIG_CONSOLE_CAR_BUFFER_SIZE bytes |
+---------------------------------------+
| ROM stage CAR_GLOBAL variables |
+---------------------------------------+ Offset 0
There was some hard coded offsets in the reference code wrapper to start
the heap past the console buffer. Even with this commit the console
can smash into the following region depending on what size
CONFIG_CONSOLE_CAR_BUFFER_SIZE is.
As noted above This change splits the CAR region into 2 parts starting
at CONFIG_DCACHE_RAM_BASE:
+---------------------------------------+
| MRC Region |
| CONFIG_DCACHE_RAM_MRC_VAR_SIZE bytes |
+---------------------------------------+ Offset CONFIG_DCACHE_RAM_SIZE
| ROM stage stack |
| |
| |
+---------------------------------------+
| ROM stage console |
| CONFIG_CONSOLE_CAR_BUFFER_SIZE bytes |
+---------------------------------------+
| ROM stage CAR_GLOBAL variables |
+---------------------------------------+ Offset 0
Another variable was add, CONFIG_DCACHE_RAM_ROMSTAGE_STACK_SIZE,
which represents the expected stack usage for the romstage. A marker
is checked at the base of the stack to determine if either the stack
was smashed or the console encroached on the stack.
Change-Id: Id76f2fe4a5cf1c776c8f0019f406593f68e443a7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2752
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The acpi_fill_mcfg() was still using ivy/sandy PCI device ids which Hawell
obviously doesn't have. This resulted in an empty MCFG table. Instead of
relying on PCI device ids use dev/fn 0/0 since that is where the host
bridge always resides. Additionally remove the defines for the IB and SB
pci device ids. Replace them with mobile and ult Haswel device ids and
use those in the pci driver tables for the northbridge code.
Booted to Linux and noted that MCFG was properly parsed.
Change-Id: Ieaab2dfef0e9daf3edbd8a27efe0825d2beb9443
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2748
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SMM handler resides in the TSEG region which is far above
CONFIG_RAM_TOP (which is the highest cacheable address) before
MTRRs are setup. This means that calling initialize_cpus() before
performing MTRR setup on the BSP means the SMM handler is copied
using uncacheable accesses.
Improve the SMM handler setup path by enabling performing MTRR setup on
for the BSP before the call to initialize_cpus(). In order to do this
the haswell_init() function was split into 2 paths: BSP & AP paths.
There is a cpu_common_init() that both call to perform similar
functionality. The BSP path in haswell_init() then starts the APs using
intel_cores_init(). The AP path in haswell_init() loads microcode and
sets up MTRRs.
This split will be leveraged for future support of bringing up APs in
parallel as well as adhering to the Haswell MP initialization
requirements.
Change-Id: Id8e17af149e68d708f3d4765e38b1c61f7ebb470
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2746
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There was a mix of setup code sprinkled across the various components:
southbridge code in the northbridge, etc. This commit reorganizes the
code so that northbridge code doesn't initialize southbridge components.
Additionally, the calling dram initialization no longer calls out to ME
code. The main() function in the mainboard calls the necessary ME
functions before and after dram initialization.
The biggest change is the addition of an early_pch_init() function
which initializes the BARs, GPIOs, and RCBA configuration. It is also
responsible for reporting back to the caller if the board is being
woken up from S3. The one sequence difference is that the RCBA config
is performed before claling the reference code.
Lastly the rcba configuration was changed to be table driven so that
different board/configurations can use the same code. It should be
possible to have board/configuration specific gpio and rcba
configuration while reusing the romstage code.
Change-Id: I830e41b426261dd686a2701ce054fc39f296dffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2681
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SMRR takes precedence over the MTRR entries. Therefore, if the TSEG
region is setup as cacheable through the MTTRs, accesses to the TSEG
region before SMM relocation are cached. This allows for the setup of
SMM relocation to be faster by caching accesses to the future TSEG
(SMRAM) memory.
MC MAP: TOM: 0x140000000
MC MAP: TOUUD: 0x18f600000
MC MAP: MESEG_BASE: 0x13f000000
MC MAP: MESEG_LIMIT: 0x7fff0fffff
MC MAP: REMAP_BASE: 0x13f000000
MC MAP: REMAP_LIMIT: 0x18f5fffff
MC MAP: TOLUD: 0xafa00000
MC MAP: BGSM: 0xad800000
MC MAP: BDSM: 0xada00000
MC MAP: TESGMB: 0xad000000
MC MAP: GGC: 0x209
TSEG->BGSM:
PCI: 00:00.0 resource base ad000000 size 800000 align 0 gran 0 limit 0 flags f0004200 index 4
BGSM->TOLUD:
PCI: 00:00.0 resource base ad800000 size 2200000 align 0 gran 0 limit 0 flags f0000200 index 5
Setting variable MTRR 0, base: 0MB, range: 2048MB, type WB
Setting variable MTRR 1, base: 2048MB, range: 512MB, type WB
Setting variable MTRR 2, base: 2560MB, range: 256MB, type WB
Adding hole at 2776MB-2816MB
Setting variable MTRR 3, base: 2776MB, range: 8MB, type UC
Setting variable MTRR 4, base: 2784MB, range: 32MB, type UC
Zero-sized MTRR range @0KB
Allocate an msr - basek = 00400000, sizek = 0023d800,
Setting variable MTRR 5, base: 4096MB, range: 2048MB, type WB
Setting variable MTRR 6, base: 6144MB, range: 256MB, type WB
Adding hole at 6390MB-6400MB
Setting variable MTRR 7, base: 6390MB, range: 2MB, type UC
MTRR translation from MB to addresses:
MTRR 0: 0x00000000 -> 0x80000000 WB
MTRR 1: 0x80000000 -> 0xa0000000 WB
MTRR 2: 0xa0000000 -> 0xb0000000 WB
MTRR 3: 0xad800000 -> 0xae000000 UC
MTRR 4: 0xae000000 -> 0xb0000000 UC
I'm not a fan of the marking physical address space with MTRRs as being
UC which is PCI space, but it is technically correct.
Lastly, drop a comment describing AP startup flow through coreboot.
Change-Id: Ic63c0377b9c20102fcd3f190052fb32bc5f89182
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2690
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Devoutly to be wish'd. To die,—to sleep;—
To sleep! perchance to dream:—ay, there's the rub;
For in that sleep of death what dreams may come,
(Since who could argue with William Shakespeare?)
Change-Id: I4e4c617dcd3ede81a0abbe16f9916562d24fa8ce
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/2733
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
It's possible that TOUUD can be 4GiB in a small physical memory
configuration. Therefore, don't add a 0-size memory range resouce
in that case.
Change-Id: I016616a9d9d615417038e9c847c354db7d872819
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2691
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Link native graphics commit 49428d84 [1]
Add support for Google's Chromebook Pixel
was missing some of the higher level bits, and hence could not be
used. This is not new code -- it has been working since last
August -- so the effort now is to get it into the tree and structure
it in a way compatible with upstream coreboot.
1. Add options to src/device/Kconfig to enable native graphics.
2. Export the MTRR function for setting variable MTRRs.
3. Clean up some of the comments and white space.
While I realize that the product name is Pixel, the mainboard in the
coreboot tree is called Link, and that name is what we will use
in our commits.
[1] http://review.coreboot.org/2482
Change-Id: Ie4db21f245cf5062fe3a8ee913d05dd79030e3e8
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2531
Tested-by: build bot (Jenkins)
This wasn't previously spotted because the printk's were correct.
However if one needed to get the value of the BDSM or BGSM register
the value would reflect the other register's value.
Change-Id: Ieec7360a74a65292773b61e14da39fc7d8bfad46
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2689
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Add ME device ID for Lynxpoint LP
- Add GPU device IDs for ULT
- SATA init tweaks from checking against DXE reference code
- Remove the ICH7 from the SPI driver so it works on all lynxpoint
without having to add more LPC device ID checks
- Add function disable for audio dsp and xhci, remove PCI bridge
- Add interrupt route registers for new devices (needs romstage setup)
Change-Id: Idb48f50d0bacb6bf90531c3834542b9abb54fb8a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2680
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Device IDs for northbridge and GPU.
Also mask off the lock bit in the memory map registers.
Change-Id: I9a4955d4541b938285712e82dd0b1696fa272b63
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2646
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Some of the Lynx Point ids were off. Correct those and make
the pei data BAR fields consistent with the others.
Change-Id: I4102439588362cdb94643bd1ce69c9fa4278329e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2622
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
