mtrr_use_temp_range is a lot smarter than the plain set_var_mtrr. It
will compute a new optimal solution with the temp ranges included
while also taking care of the cleanup before loading the payload/s3
resume.
Change-Id: I283ba07fc12c410be39dfdc828657598237247c1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63550
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Increase frequency of sc7280 to 75 MHz. Setting the delay to 1/8 of
a cycle as a result of experimentation.
BUG=b:190231148
BRANCH=None
TEST=Make sure that herobrine board boots
HW Engineer measured SPI frequency and verified running at 75 MHz
Signed-off-by: Shelley Chen <shchen@google.com>
Change-Id: I3cf5a7c85f12800a11ece397a354349f2a0a235f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64673
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The patch uses coreboot error codes instead of uint8_t data type in the
pre_mem_debug_init function.
TEST=build code for Gimble
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I957ff764900cb789bf2aacf0472dcb281f48af07
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Now that the FSP provides the ALIB ACPI table via a HOB, the PNOT power
notify method can call WAL1 which will then call ALIB to communicate the
current AC/DC state to the SMU.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic966b73aa28f329207f8d840ca5fb5f2bf6ec9b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64667
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Under the current watchdog setting, the system will not reboot when the
temperature is too high. To enable thermal hardware reset, we need to
enable thermal control request and set it to reboot mode.
Note that because thermal throttle (by lowering cpu frequency) is
currently enabled, the thermal hardware reset shouldn't be triggered
under normal circumstances.
This feature is only for new hardware structure for thermal. Therefore,
we only need to apply it on MT8192/MT8195/MT8186.
This setting is based on thermal and watchdog section of MT8192
Function Specification.
BUG=none
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I98b062c2070384527624c3bcf0dfded25a2c8ce4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64676
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Under the current watchdog setting, the system will not reboot when the
temperature is too high. To enable thermal hardware reset, we need to
enable thermal control request and set it to reboot mode.
Note that because thermal throttle (by lowering cpu frequency) is
currently enabled, the thermal hardware reset shouldn't be triggered
under normal circumstances.
This feature is only for new hardware structure for thermal. Therefore,
we only need to apply it on MT8192/MT8195/MT8186.
This setting is based on thermal and watchdog section of MT8195
Function Specification.
BUG=none
TEST=build pass
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ia6489bb953d148a43af173454d6f2b3e2a1dfcf9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64675
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Under the current watchdog setting, the system will not reboot when the
temperature is too high. To enable thermal hardware reset, we need to
enable thermal control request and set it to reboot mode.
Note that because thermal throttle (by lowering cpu frequency) is
currently enabled, the thermal hardware reset shouldn't be triggered
under normal circumstances.
This feature is only for new hardware structure for thermal. Therefore,
we only need to apply it on MT8192/MT8195/MT8186.
This setting is based on thermal and watchdog section of MT8186
Function Specification.
BUG=none
TEST=emerge-corsola coreboot
TEST=thermal hardware reset is working.
Signed-off-by: Runyang Chen <runyang.chen@mediatek.corp-partner.google.com>
Change-Id: Id2ed55e6d4f4eec450bf7c849f726a389eeb6694
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64659
Reviewed-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Based on the constraints for CML.
Fixes the following warnings in Linux on system76/oryp8 and
system76/gaze16, which have an NVIDIA GPU on the bridge.
pcieport 0000:00:01.0: can't derive routing for PCI INT A
pcieport 0000:00:01.0: can't derive routing for PCI INT B
This, in turn, resolves an IRQ conflict with the PCH HDA device that
would cause a stack trace on every boot and on S3 suspend.
irq 10: nobody cared (try booting with the "irqpoll" option)
<snip>
[<00000000fb84c354>] azx_interrupt [snd_hda_codec]
Disabling IRQ #10
Change-Id: Ibc968aaa7bf0259879097ff69d2543dcfa2e5e4b
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Select `HAVE_HYPERTHREADING` and hook up the hyper-threading setting
from the FSP to the option API so that related mainboards don't have to
do that. Unless otherwise configured (e.g. the CMOS setting or overriden
by the mainboard code), the value from the Kconfig setting
`FSP_HYPERTHREADING` is used.
Change-Id: I520a936b4c3a8997ba2c6bea0126b3bbcc5d68ce
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Select `HAVE_HYPERTHREADING` and hook up the hyper-threading setting
from the FSP to the option API so that related mainboards don't have to
do that. Unless otherwise configured (e.g. the CMOS setting or overriden
by the mainboard code), the value from the Kconfig setting
`FSP_HYPERTHREADING` is used.
Also, remove related code from the mainboard starlabs/laptop/tgl, since
it is obsolete now.
Change-Id: I49bbd4a776b4e6c55cb373bbf88a3ca076342e3e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Select `HAVE_HYPERTHREADING` and hook up the hyper-threading setting
from the FSP to the option API so that related mainboards don't have to
do that. Unless otherwise configured (e.g. the CMOS setting or overriden
by the mainboard code), the value from the Kconfig setting
`FSP_HYPERTHREADING` is used.
Also, remove related code from the following mainboards, since it is
obsolete now.
* siemens/chili
* starlabs/laptop/cml
Change-Id: I173b87da5ce76549672c50ba30204cd77be8b82f
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Move the Kconfig option `FSP_HYPERTHREADING` to common Intel Kconfig so
that it can be reused by other SoCs. Since not all SoCs support
hyperthreading, make it conditional on `HAVE_HYPERTHREADING`. SoCs
supporting hyperthreading need to select it so that `FSP_HYPERTHREADING`
is available.
Change-Id: I892d48b488cbf828057f0e9be9edc4352c58bbe7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The patch skips sending DISCONNECT IPC command to PMC if system resumes
from S3.
coreboot notice DISCONNECT IPC command getting timedout during S3
resume if system has AC connected behind Type-C hub. This impacts
system resume time. Please refer TA# 730910 for more information.
coreboot need not send the DISCONNECT IPC command when system resumes
from S3 state.
TEST=Verified system boots to OS and verfied below tests on Gimble
1. coreboot doesn't send the DISCONNECT during S3 resume
2. After S3 resume, system detects the pen drive with Superspeed
3. After system resumes from S3, hot-plug the pen drive, system detects
the pen drive
3. System sends IPC commands when system boots from S0 or S5.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I6ad006ae8677919c7dfeca8eec0af11454a2e89d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
The FSP includes a UPD to set the DPA (Dynamic Periodicity
Alteration) PreWake value, which can be used to set the maximum
pre-wake randomization time in "micro-ticks". This patch adds
support for configuring that value.
BUG=b:228410327
TEST=build FW and checked DPA value by fsp log.
Signed-off-by: leo.chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I08897c590a88aba058cb9e364185ea0794e1e7c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch drops the unused `PCH_DEV_SLOT_LPC` macro from the
Tiger Lake SoC PCI device list.
BUG=none
TEST=Able to build and boot volteer, google board.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I27a2f31aa706c4d76e9f0db202422bc129368959
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
SCP core 2 is enabled for MT8195 camera feature. It requires the same
register access permission as SCP core 1. Therefore, we configure the
same domain ID for both cores.
BRANCH=cherry
BUG=b:193814857
TEST=cherry boot ok
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Change-Id: Idf335593936b12c083c926a252fa99c3b76cda6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64575
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All targets now use cbmem for the BERT region, so the implementation can
be common.
This also drops the obsolete comment about the need to have bert in a
reserved region (cbmem gets fixed to be in a reserved region).
Change-Id: I6f33d9e05a02492a1c91fb7af94aadaa9acd2931
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This removes the need to align BERT so that TSEG remains aligned.
Change-Id: I21b55a87838dcb4bd4099f051ba0a011a4d41eea
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Since the FIT pointer is patched at runtime there is no guarantee that
the pre-defined one will match the patched one. Add a check and print a
warning at runtime if both addresses (pre-defined and patched) do not
match as in this case an offline computed hash for the bootblock will
differ from the runtime one.
Change-Id: Ib1b02ec43af183caa9f5b08b3c485879b423c40f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Before TXE releases the CPU out of reset a pointer to the constructed
FIT in SRAM is patched into the loaded bootblock at offset 4G - 64B.
Since this patched bootblock gets measured during runtime it will not
match the one that is potentially measured from the coreboot image.
This patch adds a dedicated fit.c file for Apollo Lake where the FIT
pointer is already set to the address TXE will be using at runtime.
Test=Compare sha256 sum from coreboot runtime and coreboot.rom of the
bootblock and make sure they match.
Change-Id: Ia0fd2a19517c70f50ef37e6a2dc2408bae28df10
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
On Apollo Lake the bootblock is stitched into the IBBL IFWI region at
build time. At execution time TXE loads this IBBL into a shared SRAM
(which is read-only in this phase) and maps it at 4 GiB - 32 KiB. Then
the CPU starts to operate from this shared SRAM as it were flash space.
In order to provide a reliable CRTM init, the real executed bootblock
code needs to be measured into TPM if VBOOT is selected. This patch adds
the needed code to do this.
Change-Id: Ifb3f798de638a85029ebfe0d1b65770029297db3
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
On platforms where the bootblock is not included in CBFS anymore
(because it is part of another firmware section (IFWI or a different
CBFS), the CRTM measurement fails.
This patch adds a new function to provide a way at SoC level to measure
the bootblock. Following patches will add functionality to retrieve the
bootblock from the SoC related location and measure it from there.
In this way the really executed code will be measured.
Change-Id: I6d0da1e95a9588eb5228f63151bb04bfccfcf04b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add the boot flash MMIO window to the resources to report this region as
reserved to the OS. This is done to stay consistent with the reserved
memory ranges by coreboot and make the OS aware of them.
As x86 systems preserves the upper 16 MiB below 4G for BIOS flash
decoding use the complete window for reporting independent of the
actually used SPI flash size. This will block the preserved MMIO window.
Change-Id: Ib3a77e9233c3c63bad4de926670edb4545ceaddf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch drops the unused `PCH_DEV_SLOT_LPC` macro from the
Alder Lake SoC PCI device list.
BUG=none
TEST=Able to build and boot taeko, google board.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib2ae40fcc4499de34534f27f03b4c359c37409e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Since the fast SPI controller is hidden on Apollo Lake the OS cannot
probe it and is therefore unaware of the reserved resources assigned in
coreboot. Select 'FAST_SPI_GENERATE_SSDT' to enable SSDT creation to
report the reserved resources to the OS.
Change-Id: I23e77a0a01141dc4f299988d19509e6df555a654
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
This patch provides the possibility for EHL based boards to disable
RAPL settings via SOC_INTEL_DISABLE_POWER_LIMITS config switch.
On Elkhart Lake the way via setting relevant MSR bits does not work.
Therefore the way via MCHBAR is choosen.
Test:
Check MCHBAR mapped registers (MCH_PKG_POWER_LIMIT) on mc_ehl1.
Change-Id: I5be6632b15ab8e14a21b5cd35152f82fec919d9f
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
EHL MAC side expects a rising edge signal for an IRQ. Based on the
mainboard wiring it could be necessary to change the interrupt polarity.
This patch provides the functionality to invert a falling edge signal
that comes from an external PHY. The inverting can be activated via
devicetree parameter.
Change-Id: Ia314014c7cacbeb72629c773c8c0bb5f002a3f54
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Hook Timer8254ClkSetting to `legacy_8254_timer` cmos option. If that
isn't set, fallback to the `USE_LEGACY_8254_TIMER` Kconfig option.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I4f91cc2c8f48e9da47399059386092314b631b08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
If the SPI controller is hidden from the OS (which is default on Apollo
Lake) then OS has no chance to probe the device and therefore can not be
aware of the resources this PCI device occupies. If the OS needs to move
some resources for a reason it can happen that the new allocated window
will be shadowed by the hidden PCI device resource and hence causing a
conflict. As a result this MMIO window will be inaccessible from the OS
which will cause issues in applications. For instance on Apollo Lake
this causes flashrom to stop working.
This patch adds a SSDT extension for the PCI device if it is hidden from
the OS and reports the occupied resource via ACPI to the OS. For the
cases where the device is hidden later at coreboot runtime and therefore
is not marked as hidden in the PCI device itself a Kconfig switch called
'FAST_SPI_GENERATE_SSDT' is introduced. It defaults to 'no' and can be
set from SOC code to override it.
Since there is no defined ACPI ID for the fast SPI controller available
now, the generic one (PNP0C02) is used.
Test: Boot mc_apl4 and make sure flashrom works again.
Change-Id: Ia16dfe6e001188aad26418afe0f04c53ecfd56f1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Use defines for a better reading of the code.
Change-Id: I8e696240d649c0ea2341b8f04b62eebffebc1d57
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64519
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
By right if PseTsnGbeSgmiiEnable is disable,
PseTsnGbePhyInterfaceType should use RGMII setting.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: If593a5534716a9e93f99cb155fb5e86e12b1df17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
There are efforts to have bootflows that do not follow a traditional
bootblock-romstage-postcar-ramstage model. As part of that CBMEM
initialisation hooks will need to move from romstage to bootblock.
The interface towards platforms and drivers will change to use one of
CBMEM_CREATION_HOOK() or CBMEM_READY_HOOK(). Former will only be called
in the first stage with CBMEM available.
Change-Id: Ie24bf4e818ca69f539196c3a814f3c52d4103d7e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
In order to pass PCIe base address to payloads, implement pcie_fill_lb()
to fill coreboot table with PCIe info.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, here is the SSD information in boot log:
== NVME IDENTIFY CONTROLLER DATA ==
PCI VID : 0x15b7
PCI SSVID : 0x15b7
SN : 21517J440114
MN : WDC PC SN530 SDBPTPZ-256G-1006
RAB : 0x4
AERL : 0x7
SQES : 0x66
CQES : 0x44
NN : 0x1
Identified NVMe model WDC PC SN530 SDBPTPZ-256G-1006
BUG=b:178565024
BRANCH=cherry
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: Ib2988694f60aac9cbfc09ef9a26d47e01c004406
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Follow this commit 95986169f (soc/intel/alderlake: Skip FSP Notify APIs)
to skip FSP Notify APIs.
Elkhart Lake SoC deselects Kconfigs as below:
- USE_FSP_NOTIFY_PHASE_READY_TO_BOOT
- USE_FSP_NOTIFY_PHASE_END_OF_FIRMWARE
to skip FSP notify APIs (Ready to boot and End of Firmware) and make
use of native coreboot driver to perform SoC recommended operations
prior booting to payload/OS.
When deselecting these Kconfigs, cse_final_ready_to_boot() and
cse_final_end_of_firmware() in the common cse driver will be used
instead as required operations to perform prior to booting to OS.
Check out this CL for further info:
commit 90e318bba (soc/intel/common/cse: Add `finalize` operation for
CSE)
Additionally, create a helper function `heci_finalize()` to keep HECI
related operations separated for easy guarding again config.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I477c204233f83bc96fd5cd39346bff15ed942dc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Remove two redundant `void *` casts in `clrsetbits32()` calls. In
addition, preemptively retype the `io_mem_base` variable in order
to avoid having to add casts in future commits.
Change-Id: Iae9c8189a6f8cd29181c52c2241789c6d392d77b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
This patch adds the support to enable the external V1P05/Vnn rails
in S0 state via devicetree.
BUG=b:223102016
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I555e5607af15a5f5d83ef74321b1b71f17cca289
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
This patch updates the VccIn Aux Imon IccMax for ADL-N to SOC SKU
specific value of 27A.
Kit: 646929 - ADL N Platform Design Guide
BUG=b:223102016
TEST=Verified that VccIn Aux Imon IccMax value is set to 27mA.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: If09cd1112fac9b30ff04c45aa5a6062c2513c715
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
There are two APL specific config switches for RAPL and min. cpu clock
(APL_SKIP_SET_POWER_LIMITS, APL_SET_MIN_CLOCK_RATIO). These switches
could be used in future in other CPU platforms. Move them to common code
instead of having them just for one SOC.
Test: Make sure that the clock ratio (MSR 0x198) and the RAPL settings
(MSR0x610) do not change with this patch applied on mc_apl{1,4,5}
mainboard.
Change-Id: I3d63d1b9b6c96586a3c20bf8c1d8001b1d7c4bed
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Program the `SmbusEnable` FSP UPD according to the SMBus PCI device's
state in the devicetree. This avoids having to manually make sure the
SMBus PCI device and the `SmbusEnable` setting are in sync.
Change-Id: I275a981f914a55dc57a75e7d436912ff0255a293
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64402
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The psp_notify_boot_done call is done at the entry of BS_PAYLOAD_BOOT,
so it's not guaranteed that the psp_set_spl_fuse call is done before the
psp_notify_boot_done call. Moving the psp_set_spl_fuse call makes sure
that it's done before the psp_notify_boot_done call. This also brings
the psp_set_spl_fuse call in line with the enable_secure_boot call that
sends the PSB fusing command to the PSP.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id76b462608c3d788cd90e73a64d18c8e8b89dbfd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Hook up the hyper-threading setting from the FSP to the option API so
that related mainboards don't have to do that. Unless otherwise
configured (e.g. the CMOS setting or overriden by the mainboard code),
the value from the Kconfig setting `FSP_HYPERTHREADING` is used.
Also, remove related code from the mainboard kontron/bsl6, since it is
obsolete now.
Change-Id: I1023d1b94acb63f30455c56b394b68059deaaa16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
mcfg->usb_phy is a pointer to a struct usb_phy_config. The config is
constant. Changing a constant is undefined behavior, so create a local
static instance of usb_phy_config that can be modified safely.
Change-Id: If9b76b869a5b0581f979432ce57cc40f1c253880
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add and use defines instead of magic values in fsp_m_params.c.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie0e33eb0af5310ab4610ea8951688464c4960260
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64126
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
