This change reorganizes FMAP for volteer to make use of the lower
16MiB of the SPI flash for RW_SECTION_A and RW_MISC in addition to
RW_LEGACY. This is now possible because TGL supports memory mapping of
BIOS region greater than 16MiB.
Following changes are made in chromeos.fmd as part of this:
1. Move RW_SECTION_A and RW_MISC to lower 16MiB.
2. Reduce size of RW_LEGACY to 2MiB since we longer need to use it as
a placeholder in the lower half of the SPI flash.
3. Reduce size of RW_ELOG to 4KiB as coreboot does not support a
larger region for ELOG.
4. Increase WP_RO to 8MiB to allow larger space for firmware
screens. GBB size is thus increased to 448KiB.
BUG=b:171534504
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I0c3c0af94183a80c23d196422d3c8cf960b9d9f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
AP_PEN_DET_ODL isolated by a diode and need to pull up internally.
BUG=b:160752604
BRANCH=dedede
TEST=Build and confirm waveform by google EE parter.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I85f3d0209094af07891a5c0cc218443da586e6e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48294
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change restricts RW_DIAG region to lower 16MiB to ensure that the
extended BIOS checker for FMAP does not complain about 16MiB boundary
crossing.
I haven't updated any other regions to occupy the newly freed space
but it is fine since this board is dead and should be dropped from
coreboot soon.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I19ab204fbe3e020e42baf68bfa350dcff32066a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch adds the PMC MUX and CONx devices for lindar. Device
specific method contains the port and orientation details used
to configure the mux.
BUG=b:172533907
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Id5ee78b7ece8421144086af9b95f5f0d849be56c
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
SATA_AHCI is already the default mode for CNL based mainboards.
Therefore, remove its configuration from all related devicetrees.
Built clevo/l140cu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: I814e191243224a4b021cd7d4c1b611316f1fd1a4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Align the SATA mode names with soc/skl providing a consistent API.
Built clevo/l140cu with BUILD_TIMELESS=1, coreboot.rom remains
identical.
Change-Id: I54b48462852d7fe0230dde0c272da3d12365d987
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Update lindar gpio settings for Synaptics trackpad no function issue.
Update I2C5 bus freq to 400kHz.
Improve Goodix Touchscreen power on sequence.
BUG=b:160013582
BRANCH=firmware-volteer-13521.B
TEST=emerge-volteer coreboot and check system dmesg and evtest can get
device. Verify trackpad function workable.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I8c1ab6bab1f9de187e2a78ead7b5bbaf758f5fcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Unique among the Volteer devices, the volteer2_ti50 variant connects to
the TPM via I2C. This CL introduces the proper devicestree declarations
for the Linux kernel to recognize that.
overridetree.cb is shared between "sub"-variants volteer2 and
volteer2_ti50, so both will have two TPM nodes, the I2C being disabled
by default. The odd _ti50 variant then has code in variant.c to enable
the I2C node and disable the SPI node.
BUG=b:173461736
TEST=abuild -t GOOGLE_VOLTEER2{_TI50,} -c max -x
Change-Id: I5576a595bbabc34c62b768f8b3439e35ff6bcf7b
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48223
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update Power Limit2 (PL2) minimum value to the same as maximum value for
volteer variants like baseboard, delbin, eldrid, terrador and todor.
All other variants uses the DTT entries from baseboard devicetree since
there is no override present for those variants. DTT does not throttle PL2,
so this minimum value change here does not impact any existing behavior on
the system.
BUG=None
BRANCH=volteer
TEST=Build and test on volteer system
Change-Id: I568e87c87ef517e96eaab3ff144b1674d26ae1e6
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
refer to cb:45878
Now that soc_get_pmc_mux_device() is gone, the PMC MUX connector devices
can be hooked up together via devicetree aliases.
BUG=b:174735512
BRANCH=volteer
TEST=build and type-c display work
Change-Id: I0bf84e2691856c9760d8fa9b6d853b04be10390a
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48268
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the storo variant of the waddledee reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.3.1).
BUG=b:174284884
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_STORO
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I5ad41e0b2bc95b44733a2ad3c543267f3f56f9e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
DPTF paramerters form thermal team.
Set PL1 Min/Max 15/25W, PL2 Min/Max 40/49W.
BUG=b:174514010
BRANCH=puff
TEST=build image and verified by thermal team.
Change-Id: I9e6c4bae181e87f87f2e92337bb9d989f5b7d955
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
set APU_EDP_BL_DISABLE(GPIO_85) to low to avoid the VARY_BL fast than
APU_DP_BLON.
BUG=b:171954512
BRANCH=zork
TEST=validate the panel sequence with scope.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ia6d3f4335583bb2d91a6bce96d89cff84247d0ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Create the copano variant of the volteer reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.3.1).
BUG=b:174413884
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_COPANO
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ib06625f492f68a6a6f5c6b382772b68f1eb681ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
According to the spec provided by Bayhub, the 3.3V power rail must be enabled at least 100ms before reset is released.
To ensure this, set the power enable signal in the bootblock GPIO table.
BUG=b:173676531
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS, test USB function normally.
Change-Id: I0c536f36c138ace93766f3024f6ec5d47b38269f
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47799
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use a new driver for the SX9324 proximity detector device.
This is first draft settings, will modify it after fine tuning.
BUG=b:172397658
BRANCH=zork
TEST=run "i2cdump -y -f 0 0x28" and checked all registers are expected.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I869d0b6640247099ca489e96ed94e03811a04bf4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47867
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Latest HW schematic add LTE_RST pin to control module power sequence.
BUG=b:173490220
BRANCH=zork
TEST=measure the waveform is meet the LTE module spec.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I0f0a35a905d711dd8d17dea2ae82a8dfa1fa05ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable Acoustic noise mitigation for drawcia and set slew rate to 1/4
which is calibrated value for the board. Other values like PreWake,
Rampup and RampDown are 0 by default.
BUG=b:162192346
BRANCH=dedede
TEST=Correct value is passed to UPD and Acoustic noise test passes.
Change-Id: Iadcf332d59dac2ba191b82742a18a1ab326940d1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Initiate device tree based on latest schematic.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia94119cb6d7eff6ea13c7d6a7dfd6ce891f706fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add implementation of EC smihandler
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I211f5755ff44514ab7ab4083f684ddd88c23fe48
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48115
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable building for Chrome OS and add associated ACPI configuration.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I5311879a127a2c8da1bbb086449019d932d57b72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This is used as a signal to show the system state. It hadn't been used
up to this point as we're not currently using S0i3, but the fingerprint
sensor will use it to go into a low power mode, so set it appropriately
on Trembyle. Dalboz devices don't use the FPMCU, but set there as well
so that the state matches.
BUG=b:174695987
TEST=Verify GPIO state in S0 and S3 with the EC
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ibc725905909830d44f77c2498a26edf6d7a3dc05
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48255
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Vincent Palatin <vpalatin@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add stubbed out GPIO configuration and perform GPIO initialization
during bootblock and ramstage.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia658ab4b466242cf8658abb239f19a9c0a03849a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add entry point stubs of each stage for Brya. More functionalities will
be added later.
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I44934c05ee32090b6e34648ee02f004c83e93d57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48063
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:174266035
TEST=Build Test
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia1ba8c997680c60ee1eabfae82459e127f664117
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48062
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch renames cbfs_boot_map_with_leak() and cbfs_boot_load_file()
to cbfs_map() and cbfs_load() respectively. This is supposed to be the
start of a new, better organized CBFS API where the most common
operations have the most simple and straight-forward names. Less
commonly used variants of these operations (e.g. cbfs_ro_load() or
cbfs_region_load()) can be introduced later. It seems unnecessary to
keep carrying around "boot" in the names of most CBFS APIs if the vast
majority of accesses go to the boot CBFS (instead, more unusual
operations should have longer names that describe how they diverge from
the common ones).
cbfs_map() is paired with a new cbfs_unmap() to allow callers to cleanly
reap mappings when desired. A few new cbfs_unmap() calls are added to
generic code where it makes sense, but it seems unnecessary to introduce
this everywhere in platform or architecture specific code where the boot
medium is known to be memory-mapped anyway. In fact, even for
non-memory-mapped platforms, sometimes leaking a mapping to the CBFS
cache is a much cleaner solution than jumping through hoops to provide
some other storage for some long-lived file object, and it shouldn't be
outright forbidden when it makes sense.
Additionally, remove the type arguments from these function signatures.
The goal is to eventually remove type arguments for lookup from the
whole CBFS API. Filenames already uniquely identify CBFS files. The type
field is just informational, and there should be APIs to allow callers
to check it when desired, but it's not clear what we gain from forcing
this as a parameter into every single CBFS access when the vast majority
of the time it provides no additional value and is just clutter.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib24325400815a9c3d25f66c61829a24a239bb88e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39304
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Mariusz Szafrański <mariuszx.szafranski@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch flips the default of CONFIG_NO_CBFS_MCACHE so the feature is
enabled by default. Some older chipsets with insufficient SRAM/CAR space
still have it explicitly disabled. All others get the new section added
to their memlayout... 8K seems like a sane default to start with.
Change-Id: I0abd1c813aece6e78fb883f292ce6c9319545c44
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
At least a part or the remaining definitions in the soc-specific smi.h
files are also common, but those have to be verified more closely.
Change-Id: I5a3858e793331a8d2ec262371fa22abac044fd4a
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Add the fw_config entries for the newly added boot device fields.
These are added as separate fields since a board may have more
than one selected.
BUG=b:173129299
TEST=abuild google/volteer
Change-Id: I2af9ffcf0b90d4f4b7f2f31613ee110d8f350454
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
The initial commit only focused on GL9755S and RTS5261, but there
were recently other cards added to the fw_config and those also
need to be added to the probe lists.
BUG=b:173207454
TEST=abuild google/volteer
Change-Id: Ic27074a016ffbd4c4dd86104a6d85437357c4b82
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Default VBT supports only integrated Display port. Drawman supports a
HDMI port and hence support a separate VBT for Drawman.
BUG=b:161190931
BRANCH=dedede
TEST=Build and boot to OS in Drawlat and Drawman.
Cq-Depend: TBD
Change-Id: I8895cc67d87428eddb31328f1e3a90c346b54533
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Add daughter-board ports bit field and mask in devicetree.
BUG=b:161190931
BRANCH=dedede
TEST=Build and boot to OS in drawlat & drawman.
Change-Id: Ibbd86fc8c3e44a7d1703b8ce75c48881226545c9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Config HID-I2C device to level trigger.
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:171546871
TEST=emerge-dedede coreboot
Change-Id: If8be25f591715765a99920b79482c862b1cc7079
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
AGESA checks to make sure that the firmware version reading the MRC
cache is the same version that wrote it, so it doesn't need to be
erased during a firmware update.
BUG=b:173724014
TEST=Flash firmware to DUT, update firmware, check RW_MRC_CACHE was
not erased
BRANCH=Zork
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ice3d1d467c25366b7ef678cd6481d043f62644ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Create the drobit variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171947885
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I63b7312bba236bd5af028359804d042f6850d8ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47787
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating Imon slope and offset values as per recommendation of
ODM based on calibaration.
Updating Imon slope to 1.0 and offset to 1.4
BUG=b:167294777
BRANCH=dedede
TEST=Boot dedede platform and confirm values in FSP.
Change-Id: I3eb32218040163f0abef9b8dd4c52efb16289fe7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vinay Kumar <vinay.kumar@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Create the sasuke variant of the waddledoo reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.3.1).
BUG=b:172104731
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_SASUKE
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Change-Id: I29405d63fd266224807e535c3f86a2ad5ab8cdf3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: SH Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring
the bus frequency closer to 400kHz.
BUG=b:173670150
TEST=Verified that I2C5 frequency is between 386-387kHz.
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I6d60abe15645dc51ed9ee30975d2521b8940c2d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47736
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
