Some designs might wish to use an open drain eSPI ALERT#. This change
adds an enum that allows setting the eSPI alert mode.
BUG=b:187122344, b:186135022
TEST=Boot guybrush using all 3 alert modes
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia35fc59a699cf9444b53aad5c9bb71aa27ce9251
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The eSPI spec says that the Alert Mode defaults to in-band on reset.
This change ensures the controller is in sync with the eSPI peripheral.
The configured alert mode is configured in
espi_set_general_configuration.
BUG=b:187122344, b:186135022
TEST=Boot guybrush and make sure we don't get any eSPI errors.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib43e190d08d77ecfcd22ead2bf42e5de2202b555
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52953
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will print the config we are setting on the eSPI peripheral.
e.g.,
Setting general configuration: slave: 0x98a00000 controller: 0xe2000000
eSPI Slave configuration:
CRC checking enabled
Dedicated Alert# used to signal alert event
eSPI quad IO mode selected
Only eSPI single IO mode supported
Alert# pin is open-drain
eSPI 33MHz selected
eSPI up to 20MHz supported
Maximum Wait state: 0
BUG=b:187122344, b:186135022
TEST=Boot guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1a2382d8ab3d3f0d14a139c57470cb895112eca9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52952
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We can share this with cezanne.
BUG=b:184766519
TEST=Build picasso
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If746d55345f6b7c828376b64adc5532d20413f68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52916
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This method signature will also be used by cezanne, so move it to
common.
BUG=b:184766519
TEST=Build picasso
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I421bdad51776278f83148174e6f72bdc38249e54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
If the ACPI table size in the HOB data header is larger than the maximum
HOB payload, don't add the table at all and print an error instead,
since in this case the memcpy would read past the end of the HOB data
structure.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I965c01bd9ab66b14d6f77b6f23c28479ae6d6a50
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52897
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This function will be reused in Cezanne, so move it from the Picasso
directory to the common FSP integration code.
TEST=On Mandolin Linux finds the AMD SSDT that contains ALIB.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7b256de712fe60d1c021cb875aaadec1d331584b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The usage of external oscillator has got nothing to do with Audio
Co-processor (ACP). Hence move it out of common config and put it into
the SoC config where it is being used.
BUG=None
TEST=Build Dalboz and Vilboz mainboards.
Change-Id: I8c5d98addfba750f9ddb87a846599541b4a8340a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
We no longer lock up if we clear the port 80 bit. I'm assuming this was
fixed when we configured the PSP to no longer setup eSPI.
BUG=b:183974365
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1530d08974d42e0b06eb783521dea32fca752d85
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Temp stack for verstage is only needed for picasso, so make it optional
in the layout file.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I44196103a3531e9d01c96ab8f454c8b580fe9807
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52688
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
From cezanne we have enough space in PSP so we don't have to worry about
workbuf size. Hence the function only exists in picasso and deprecated
for later platforms.
So wrap svc_get_max_workbuf_size and provide default weak function so
future platforms don't have to implement dumb function for it.
TEST=build and boot zork, check weak function is not called in zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I16e8edf8070aaacb3a6a6a8adc92b44a230c3139
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
These addresses will be changed in cezanne. Before start working on
cezanne, move these out to separate header as a clean-up.
TEST=emerge-zork coreboot
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I2499281d250aae701f86bfcc87c7681e5b684b6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Audio Co-processor driver is similar for both Picasso and Cezanne SoCs.
Hence move it to the common location.
BUG=None.
TEST=Builds Dalboz, Trembyle, Vilboz, Mandolin and Bilby mainboards.
Change-Id: I91470ff68d1c183df9a2927d71b03371b535186a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
We don't have any infrastructure setup to handle SCI SMIs. Instead of
just silently ignoring the SMI, print a warning saying that it is
being ignored.
BUG=none
TEST=Trigger an SCI SMI and see warning printed.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I803e572250925b7d5ffdbb3e8958f9aff1f808df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52674
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add defines for the Machine Check Architecture Extensions (MCAX) MSRs
and the new MCA_CTL_MASK MSRs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id78483e7df00c3e99c698c0344f38be68d1dfb72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
bl_syscall_public.h is a header file for PSP app, but was used for x86
code to get the definition of PSP_INFO. Move the definition into
psp_transfer.h and do not include bl_syscall_public.h from x86 code.
BUG=none
TEST=build psp_verstage on zork
BRANCH=none
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I0fe011652a47d0ba2939dc31ee3b83f0718a61dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52537
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
size_t is used in the code, so we should include types.h instead of
stdint.h to also have those type definitions.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I04c50de257a2d6982bfd4907eb5a1325a751919a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52582
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The linux kernel requires a valid _OSC method. Otherwise the _LPI table
is ignored.
See https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/third_party/kernel/v5.10/drivers/acpi/bus.c;l=324
Before this patch:
acpi_processor_get_lpi_info: LPI is not supported
After this patch:
acpi_processor_evaluate_lpi: ACPI: \_SB_.CP00: ACPI: Found 4 power states
BUG=b:178728116
TEST=Boot OS and verify _LPI table is parsed
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I44e554b9db6f70fdd1559105cdaee53aeb2bfbf5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The uPEP device is required to support S0i3. The device has been written
in ASL to make it easier to read and maintain. The device constraints
are purely informational. We use a dummy constraint like the Intel
platforms to keep both linux and Windows functional.
In order for this device to be used by the linux kernel the
ACPI_FADT_LOW_PWR_IDLE_S0 flag must be set. So including it
unconditionally doesn't cause any problems.
The AMD Modern Standby BIOS Implementation Guide defines two UUIDs,
one for getting the device constraints, and one for handling
notifications. This differs from the Intel specification and the linux
driver implementation. For this reason I haven't implemented any of the
notification callbacks yet.
BUG=b:178728116
TEST=Boot OS and verify _DSM is called:
[ 0.226701] lps0_device_attach: ACPI: \_SB_.PEP_: _DSM function mask: 0x3
[ 0.226722] lpi_device_get_constraints_amd: ACPI: \_SB_.PEP_: _DSM function 1 eval successful
[ 0.226723] lpi_device_get_constraints_amd: ACPI: \_SB_.PEP_: LPI: constraints list begin:
[ 0.226724] lpi_device_get_constraints_amd: ACPI: \_SB_.PEP_: LPI: constraints list end
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I2deef47eabe702efe1a0f3747c9f27bcec37464b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52445
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since there are some differences between picasso PSP svc and cezanne PSP
svc, each platform should have their own svc wrapper.
Moreover cezanne PSP will drop unused parameters from
update_psp_bios_dir and save_uapp_data so make wrapper around it.
BUG=b:182477057
BRANCH=none
TEST=build psp_verstage and boot on zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I69f998865fc3184ea8900a431924a315c5ee9133
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52307
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
psp_verstage is not specific to picasso. There might be picasso-specific
code but move everything into common as a first step. While developing
psp_verstage for cezanne picasso-specific code will move back to picasso
directory.
BUG=b:182477057
BRANCH=none
TEST=build psp_verstage on zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ifb1df0d82b972f28be2ffebd476c2553cbda9810
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The Kconfig value specified Intel instead of AMD.
BUG=b:184198808
TEST=Backlight enabled in the OS
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I9fbdf821591ec886f383c1a5ac197f8f213c4cc4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52384
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is no need to stash the SCI trigger register configuration and
apply it at the end. Remove this to make SCI and SMI programming more
symmetrical and to use available configure_scimap function instead of
implementing it again, but without the additional checks. Using this
function also allows removing soc_route_sci.
Change-Id: Ie23da79546858282910db65182a6315ade506279
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Picasso and Stoneyridge didn't do a read-modify-write operation on the
lower nibble of PM_RTC_SHADOW_REG, but just wrote the upper nibble as
all zeros. Since the upper nibble might be uninitialized before the
lower nibble gets written, do what Picasso and Stoneyridge did here
instead of what the reference code does. Also add a comment why and how
this register behaves a bit weird.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0bda2349e3ae84cba50b187cc773fd8a5b17f4e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Not selecting POWER_STATE_DEFAULT_ON_AFTER_FAILURE brings Cezanne that
is currently the only SoC using this functionality in line with Picasso
where the default is that the board remains in power off mode after
power was lost and later restored. Boards can change this behavior by
selecting POWER_STATE_OFF_AFTER_FAILURE, POWER_STATE_ON_AFTER_FAILURE or
POWER_STATE_PREVIOUS_AFTER_FAILURE.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic96f40e3c9867cd821e58d752f58b763930f6d0f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Without this being selected, mainboards can't select
MAINBOARD_POWER_STATE_PREVIOUS to use the power state restoration code
path in pmlib.c
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I753659fa753e03a66b6c6b2eb97e7ef20c71ca57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Since Cezanne needs the exact same code, move it to the common directory
and add a Kconfig option to add this functionality to the build.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I04c4295071a3df7afcb4dfd5435b11fb0bf6963f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Verified that all accessed registers exist in all SoCs that use this
code (Carrizo, Mullins, Stoneyridge, Picasso and Cezanne at the moment)
and that the bit definitions match as well. Also at the time of writing
this patch only Picasso calls gpio_fill_wake_state, so dropping the
check won't change behavior. This also avoids having SoC specific code
that doesn't get selected by Kconfig options in the common AMD SoC
directory and also avoids having to add a check for SOC_AMD_CEZANNE to
support this functionality on Cezanne in a follow-up patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If770780a67776daf81744db1b635ffd402653a47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52223
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Introduce a power management library to handle the power resume after
power failure. Enable HAVE_POWER_STATE_AFTER_FAILURE config when this
library is enabled.
BUG=b:183739671
TEST=Build Guybrush and Majolica mainboard.
Change-Id: Iea4ea57d747425fe6714d40ba6e60f2447febf28
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add GRXS and GTXS support. Move the gpio method into common place.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8ba377179d6976cf26ed0dc521d8e4eff051dc85
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52202
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This override was added to have the SCI mapping configured if GPIO was
used as WAKE_L pin. This however didn't set up the SCI level and trigger
information, so it likely never worked as intended.
Change-Id: I44661f05c8f517ece88714c625603579731d174b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This register is used for masking/unmasking eSPI IRQs.
BUG=none
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia209539b2e0ce390e227757b16c2969b9124a845
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52142
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
espi_setup already clears most of the controller registers. So this
change consolidates the clear logic into one spot.
This shouldn't result in a behavior change on Picasso. Picasso already
has the eSPI decodes clear on boot, so this change is a nop.
BUG=b:183524609
TEST=Boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic57689e50febd29796d8ac8d99c81e41fee5b41c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This is only ever called after espi_setup.
55861 - AMD System Peripheral Bus Overview also says that io ranges
should be configured before enabling the BUS_MASTER bit.
BUG=b:183524609
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I074e487d8768a578ee889a125b9948e3aa6c7269
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tidy up the interrupt status. This will leave SLAVE0_INT_STS = 0.
BUG=b:183524609
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I950cfb81521e35758c120a482670cfdb924201d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52056
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This sets the eSPI registers to the reset values specified in the PPR.
On Cezanne, the PSP modifies these registers such that the eSPI
peripheral cannot send DEFER packets. This causes random bus errors.
These reset values are identical to what is currently used on Zork.
I didn't clear out ESPI_DECODE because it's currently being done by
cb:51749.
BUG=b:183524609
TEST=Boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic3a9860747aac78121358b4499d8a38052236c0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
These are defined in the public Picasso PPR - 55570-B1 Rev 3.15.
BUG=b:183524609
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I7e601f767327e0a24a086146623af039388b2e7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52057
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Previously, the eSPI code would only add to existing decode ranges, and
there wasn't any way to clear ranges. This clears all the ranges so
the eSPI configuration can start fresh.
BUG=b:183207262, b:183974365
TEST=Verify on Guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ic4e67c40d34915505bdd5b431a064d2c7b6bbc70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
pci_rom_ssdt reloads the oprom from cbfs. It then places it into cbmem
and writes the offsets as the ROM ACPI node. The GOP driver modifies the
VBIOS so we don't want to reread from cbfs. When using GOP we also pass
the offsets with the VFCT table.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iaf53e750564f1f0e115cd354790da62e672d74b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the format warning below by using `PRIxPTR`, which is defined as
unsigned long.
src/soc/amd/common/block/smbus/smbus.c:33:56: error: format specifies type 'size_t' (aka 'unsigned int') but the argument has type 'uintptr_t' (aka 'unsigned long') [-Werror,-Wformat]
printk(BIOS_ERR, "Invalid SMBus or ASF base %#zx\n", mmio);
~~~~ ^~~~
%#lx
src/include/console/console.h:60:61: note: expanded from macro 'printk'
#define printk(LEVEL, fmt, args...) do_printk(LEVEL, fmt, ##args)
~~~ ^~~~
1 error generated.
Change-Id: I727c490d3097dcf36cdbcd4db2852cd49d11785f
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
TEST=Verified that this register and the defined bits exist in Cezanne,
Picasso, Stoneyridge, Bolton and SB800.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I32d1d577b05edab006981516a5aefd822e7b984a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch adds a pin configuration macro that supports both switching a
pin to its native function and configuring it as a SCI source. This is a
preparation to remove the GPIO2 soc_gpio_hook.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If0da5c010f35fd902f6b8857368daec93c12394a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50373
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There's no need to use a fixed-width type here.
Change-Id: I727c64661990040db356c5508fecc0a65960c095
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51794
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The correct printf format specifier for an `unsigned int` is `%u`.
Change-Id: Iaf780eb366f8c3493b89beb9a5643fa285e7825d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51793
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
commit 4f87ae1d4a introduced a regression
in the I2C initialization resulting in soc_i2c_misc_init never getting
called, since the continue statement was indented like it belonged to
the if above, but due to the missing curly braces it was outside the if
block.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Found-by: Coverity CID 1451395, 1451387
Change-Id: Id1f17ad59cba44e96881f5511df303ae90841ab3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51786
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
