Alderlake and Raptorlake SoCs support DDR4 and DDR5, which have a total
SPD size of 512 bytes. Set this as the default and remove the setting
from mainboard Kconfigs.
Change-Id: I8703ec25454a0cd55a3de70f73d2117285a833ae
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82115
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add GPP_F18 configuration in early_gpio_table.
Without this, DUT cannot get the proper state of this signal on early
phase. It allowed DUT to attempt to enter into dev mode when EC is in RW
currently, it causes the failure of autotest/firmware_DevMode.
BUG=b:337365524
TEST=built and run autotest firmware_DevMode
Change-Id: I2179bb10b431547bc35f332c74915a63495b779d
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82099
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
GPP_D14 is floating when ISH is not being used and wasting power. Add
pulldown to prevent this from happening.
BUG=b:336654954
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
make sure OS boots up
HW team validated that power usage is 20 mW lower
Change-Id: I4e19e98fa31022ece66a47402a2a4461b430ef70
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The DVI connector on this board is DVI-D (digital only), not DVI-I.
Change-Id: I74c1257efb67cfdff2ae04a42c163dd320c850a4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82112
Reviewed-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Update the pad reset config for Touchpad Interrupt from PLTRST to DEEP
so that it can still act as a wake source during S3 suspend.
BUG=b:336398012
TEST=Build Brox BIOS image and boot to OS. Suspend to S3 and wakeup
using Trackpad.
246 | 2024-04-25 16:55:18-0700 | ACPI Enter | S3
247 | 2024-04-25 16:55:34-0700 | ACPI Wake | S3
248 | 2024-04-25 16:55:34-0700 | Wake Source | GPE # | 67
249 | 2024-04-25 17:00:38-0700 | ACPI Enter | S3
250 | 2024-04-25 17:00:47-0700 | ACPI Wake | S3
251 | 2024-04-25 17:00:47-0700 | Wake Source | GPE # | 67
Also suspend to S0ix and wakeup using Trackpad.
Change-Id: If1a275e42c6c7ad743eedc9cd3320776008bfd62
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
The Fn key on Xol emits a scancode of 94 (0x5e).
BUG=b:327656989
TEST=Flash xol, boot to Linux kernel, and verify that KEY_FN is
generated when pressed using `evtest`.
Change-Id: I34ed93d9666504bfd4d439e166911e49f58e5ff5
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82069
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
This is a minimal framework that allows the build to compile.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ief4b5c75471a2ef5bedaaee9b4737510c2826b6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Remove duplicate config entry CHROMEOS_WIFI_SAR as it is
used at the baseboard.
BUG=None
TEST=emerge-rex coreboot
Change-Id: Iabf0e490103c2097f3f033036839b77b5a0bb1b3
Signed-off-by: YH Lin <yueherngl@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81226
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1.Enable CHROMEOS_WIFI_SAR flag to load a SAR table for Intel module.
2.Describe the FW_CONFIG probe for the settings on glassway.
- WIFI_SAR_0 for Intel Wi-Fi module AX211
BUG=336051631
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I9e43081c93ef17291c5d55cf262a0f4d1497447b
Signed-off-by: Daniel_Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81781
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
There are 4 different chassis types specified by vendor firmware, each
with a slightly different HWM configuration.
The chassis type to use is determined at runtime by reading a set of
4 PCH GPIOs: 70, 38, 17, and 1.
Additionally vendor firmware also provides an option to run the fans at
full speed. This is substituted with a coreboot nvram option in this
implementation.
This was tested to make fan control work on my OptiPlex 7020 SFF.
NOTE: This is superficially similar to the OptiPlex 9010's SCH5545
however the OptiPlex 9020's SCH5555 does not use externally
programmed EC firmware.
Change-Id: Ibdccd3fc7364e03e84ca606592928410624eed43
Signed-off-by: Mate Kukri <kukri.mate@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81529
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a new GPIO port cbj-sleeve for kernel driver to call. At the same
time, a new rt5645 driver is added to replace the generic driver to
parse gpio. After entering the system, it is pulled high by the kernel
to enable the MIC function.
BUG=None
TEST=MIC function is normal
Change-Id: I093be6a3e357aae389fcbe8291a9701c40b62e15
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81774
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Allow to set board specific CPU voltage regulator settings.
The VR12 compatible voltage regulator for the CPU can be configured
by two MSRs. Currently a default value is applied, which mimics the
Intel reference code and is what the BWG suggest. However most board
vendors fill in the actual VR parameters to support OC or ULV board
variants.
When the mainboard design is too different from the Intel reference
design, not updating the VR settings might result in:
- unstable system behaviour
- limited turbo performance
- excessive battery drain
- no over-clocking capability
This patch adds support to set the board specific current limit for
Icc and Igfx.
It also allows to adjust PSI1, PSI2 and PSI3, which are powerstates
used by the VR, that consume less energy when the system is idle.
Test on Lenovo X220 with full CPU load after 1 minute, compared to
previous code with default settings:
- Limiting PP0 max current below Iccmax results in less CPU performance.
RAPL readings show that less power is drawn over time.
- Limiting PP0 max current to Iccmax results in equal CPU performance.
RAPL readings show that the same power is drawn over time.
- Setting the PP0 max current to a value >> Iccmax results in equal CPU
performance. RAPL readings show that the same power is drawn over
time.
- Updating the MSR at runtime has no effect.
Change-Id: I59edab47fc4fbe0240e1dd7d25647f7549b4def2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
If the ChromiumOS EC indicates that the device has an assistant key,
we should also add it to the generated linux,keymap binding. This
commit simply does so by examining the keyboard capabilities reported by
the EC.
BUG=b:333088656
TEST=With a device that has an assistant key, flash AP FW and verify
that the key is mapped to `KEY_ASSISTANT` in the Linux kernel using
`evtest`.
Change-Id: I217220e89bce88e3045a4fc3b124954696276442
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81996
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
The DPTF parameters were defined by the thermal team.
Based on thermal table in 330817690#comment33.
Set 6w "tcc_offset" to "15" by fw_config.
BUG=b:330817690, b:290705146
BRUNCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I19100d960919dc3087fd067c24659de467eea276
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81997
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Commit 00b40090ae ("mb/google/brox: Move hda verb to variant dir")
introduces a variant-specific file for the HDA verb tables, which
commit 1bf0c3f189 ("mb/google/brox: Create lotso variant") was missing
which caused the build to fail when both patches were submitted. To fix
the tree, add this file to the newly created lotso variant.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8a85115a204d9d9447a58da71eb65b1de963023d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82014
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Create the lotso variant of the brox reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:333494257
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brox -x -a
make sure the build includes GOOGLE_LOTSO
Change-Id: I5939127f9e6abe5b792c0627d9d67e739b27083b
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
One can argue whether or not this is desirable, but disabling this means
you cannot use power from the USB ports when the board shuts down, which
is better controlled from an option, but at the very least disabled so
as to replicate default vendor firmware behaviour.
Disable deep sleep like it is disabled on all other variants.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: I660f2efebf197df055ee7b9c349e4c2b64bda6cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75139
Reviewed-by: Keith Hui <buurin@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Copied this bit from asus/p8z77-m_pro, without it a GRUB2 payload will
get stuck in an endless loop showing
Unknown key 0xff detected
whenever there is an USB device (such as a keyboard) connected.
In this mode GRUB2 is so busy showing this message repeatedly that no
other keypress ever gets handled, and thus no other remedy is possible
than a reset via mb pins and unplugging the USB device.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: Iebd433e2762a69241257e1b4f859319536a8d8f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75138
Reviewed-by: Keith Hui <buurin@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add STORAGE_UNKNOWN, STORAGE_UFS, STORAGE_NVME for storage fw_config
field to prevent depthcharge build break.
BUG=b:333325006
TEST=emerge-brox coreboot depthcharge with no errors
Change-Id: I0e220787d6ac73ec8fa2469ed958981d0801920e
Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
These machines come with a TPM1.2 device by default. It is somewhat
obsolete these days, but there is no harm in enabling it.
Change-Id: Iec05321862aed58695c256b00494e5953219786d
Signed-off-by: Mate Kukri <kukri.mate@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81827
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
WDT1 is currently enabled but gives these errors:
[ERROR] ERROR: Resource didn't fit!!!
PNP: 002e.8 60 * size: 0x8 limit: fff io
[ERROR] PNP: 002e.8 60 io size: 0x0000000008 not assigned in devicetree
Therefore, just disable it, like it is disabled on all other variants.
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Change-Id: Ie33c219eae60f55d272b261480283a02c2d502e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75144
Reviewed-by: Keith Hui <buurin@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set GPIO27 of PCH to blink before going to sleep. This blinks the
power LED. Revert after waking up.
Tested on p8z77-m. Power LED blinks in suspend.
Change-Id: Ie1b40ae17fa2ef397585b86ac82730099b611dda
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
According to a boardview, GPIO27 is connected to the front
panel power LED, and should be output.
It will be made to blink before entering S3 suspend in a follow-up.
Change-Id: I7e47f63999e8c0bfbd37e3273d33c00bc035bcbb
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Support Memory for Hynix H58G66AK6BX070 and Samsung
K3KL9L90CM-MGCT in mem_parts_used list, and generate SPD ID for these
parts.
DRAM Part Name ID to assign
H58G66AK6BX070 4 (0100)
K3KL9L90CM-MGCT 5 (0101)
BUG=b:335341310
BRANCH=firmware-nissa-15217.B
TEST=Run command "go run ./util/spd_tools/src/part_id_gen/\
part_id_gen.go ADL lp5 \
src/mainboard/google/brya/variants/glassway/memory/ \
src/mainboard/google/brya/variants/glassway/memory/\
mem_parts_used.txt"
Change-Id: Ic07ec36a8015ce6433196a93e894b818a515b954
Signed-off-by: Daniel_Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81955
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Several brya-based boards use UFS for storage, so enable the edk2 UFS
driver when using the edk2 payload.
TEST=build/boot google/brya (banshee, craaskov), verify internal boot
media functional with edk2 payload.
Change-Id: I3dc018582e974bf73c7668f78da9b81eeb038c01
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81871
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Several zork-based boards use eMMC for storage, so enable the edk2 eMMC
driver when using the edk2 payload.
TEST=build/boot google/zork (morphius, vilboz), verify internal boot
media (both eMMC and NVMe) functional with edk2 payload.
Change-Id: Ib7e98f309594554dbcf1ddd875d47c89bd9e0e44
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add config choice menu and pad configuration to put Mini PCIe port into
mSATA mode.
The vendor firmware's "Chipset->Mini PCIe / mSATA Switch" option has
been used together with the output of inteltool and intel2pm to deduce
the exact pad configuration.
Note: the vendor firmware does not autodetect the mode, and the default
setting for the port is "Mini PCIe".
Tested with Kingston SUV500MS120G mSATA SSD.
Change-Id: Ic2da1dd4252ebb5e373bc65418e321f566d4c10f
Signed-off-by: Reto Buerki <reet@codelabs.ch>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This is another readily available (used market) system.
Based on autoport.
* All peripherals should work.
* Automatic fan control as well as S3 are working.
* The board was tested to boot Linux and Windows. EHCI debug is
untested.
* When using MrChromebox edk2 with secure boot build in, the board will
hang on each boot for about 20 seconds before continuing.
There are some quirks for doing the first flash, see the documentation.
Change-Id: Idf793fe915096cf2553572964faec5c7f8526b9a
Signed-off-by: Joel Linn <jl@conductive.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
1. Remove non-use i2c address 0x10, 0x24 and 0x40 of touch IC for touch screen
2. Add new i2c address 0x5d of Goodix touch IC for touch screen
3. Add new i2c address 0x38 of Focal touch IC for touch pad
BUG=b:333804572
TEST=FW_NAME=sundance emerge-nissa coreboot chromeos-bootimage
Change-Id: I8e2c60820a07b99b69860fd4f6557b448aef2341
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Create the pujjoga variant of nissa reference board by copying the
template files to a new directory named for the variant.
Due to new_variant.py limitation that repo can no longer be used in
inside, created this CL manually following google suggestion.
BUG=b:333839287
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_PUJJOGA
Change-Id: Ia8eb11eb65f9013e83abd45eefe7705d05b8697e
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81891
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
It uses ibexpeak southbridge and should include its pch.h,
not bd82x6x's.
TEST=Timeless binary did not change.
Change-Id: Iafa83b7f3c1cd2d8ab9af51aa331ca673d9a66df
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Anything below 128K will cause SMMSTORE driver in edk2 to fail, since
a minimum of (2) 64K blocks are needed. Increase the size to 256K to
match other boards in the tree.
TEST=build/boot zork (morphius) with SMMSTORE enabled.
Change-Id: Ifd3be9b0757e270d2f106e2fbebf3991e49dec65
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Anything below 128K will cause SMMSTORE driver in edk2 to fail, since
a minimum of (2) 64K blocks are needed. Increase the size to 256K to
match other boards in the tree.
TEST=build/boot skyrim (frostflow) with SMMSTORE enabled.
Change-Id: I34f9d27c27ab7148dfc530322f741a576c348de7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Anything below 128K will cause SMMSTORE driver in edk2 to fail, since
a minimum of (2) 64K blocks are needed. Increase the size to 256K to
match other boards in the tree.
Change-Id: Ic45324b8c5bbd205e889e934c9d5dd17f7775152
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81867
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Anything below 128K will cause SMMSTORE driver in edk2 to fail, since
a minimum of (2) 64K blocks are needed. Increase the size to 256K to
match other boards in the tree.
TEST=build/boot guybrush (dewatt) with SMMSTORE enabled.
Change-Id: Ic4fdacd493d83fa3c1683a06d1276b0190f6db8b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Anything below 128K will cause SMMSTORE driver in edk2 to fail, since
a minimum of (2) 64K blocks are needed. Increase the size to 256K to
match other boards in the tree.
Change-Id: I04d57ff7f74d79118652cfe227cf223375df6472
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81865
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The karma variant, being a Chromebase, has an internal eDP output for
the built-in display whereas the fizz/endeavour variants do not. Use
separate gma-mainboard.ads files so that karma's internal panel works
properly with libgfxinit.
TEST=build google/fizz (fizz/karma) with libgfxinit enabled, ensure
correct gma-mainboard.ads file is included in the build.
Change-Id: Ia6aca538ba8c13b48aa80901222071d704b5f0c0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Create the greenbayupoc variant of the brox reference board by copying
the template files to a new directory named for the variant.
BUG=b:329530883
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brox -x -a
make sure the build includes GOOGLE_GREENBAYUPOC.
Change-Id: I90936d97b41e59c49dd92997146caf580bce1f4f
Signed-off-by: Eren Peng <peng.eren@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
These files were added after the switch.
Change-Id: I1986e4f921e0e56fe5255433d4b9216dc7c4dc59
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81856
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
