Function 'setbits16' performs an 'OR' operation with the new data and
the origin register entry. This can lead to an incorrect value in the
register which can then lead to issues.
Change-Id: I0212420be770e2ffdabebbfaf5dfbf8d99d25915
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Makes it possible to configure the maximum allowed/supported DDR memory
frequency on a per mainboard basis.
Test
- Define maximum memory frequency in mainboard devicetree.cb
- Boot into Linux and run 'sudo dmidecode --type 17' to check memory
speed
- Boot into Linux and run 'phoronix-test-suite benchmark ramspeed'
Change-Id: I9e0c7225e2141e675a20b8e3f0dbe8c0b3a29b28
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68097
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
config.h is a dependency so add it.
Change-Id: Iac87039dd43aa75d49766b9a239fbd841ca6850c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Windows hardware tests require this field not be "Reserved".
The System76 EC firmware does not report the wake type, so it is not
possible to know if the system was powered on from the power switch or
Wake-on-LAN. In the case WoL is used, this will report the wrong value.
Change-Id: I4653c6bce2a5f0a88281fc810df5646e44f90674
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Enable SRAM in devicetree so that resources are allocated properly
for it.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I1d7ee4f950b31f2be6fb7bd107b5fe54785ed81a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67420
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable the P2SB so that the SPI is discoverable by the OS.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ied7a6ea706e6da86182c109ab4813fa3fcebb1f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67419
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BRANCH=none
BUG=b:234776154
TEST=build and boot Nirwen UFS, copy ISH firmware to host
file system /lib/firmware/intel/adln_ish.bin
check "dmesg |grep ish", it should show:
ish-loader: ISH firmware intel/adlnrvp_ish.bin loaded
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I89782b0b7dde1fca0130472a38628e72dfd5c26c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
First of all, make sure that `get_board_settings()` never returns NULL.
If there's a problem, return predefined values for board settings.
If the board settings definition differs between coreboot and the BMC,
the CRC will not match. Allow coreboot to use the BMC settings provided
by older BMC firmware revisions which have less settings, if the CRC of
the first N bytes matches the expected CRC.
TEST=Boot coreboot master with BMC FW R04.05, observe board settings
being honored even though coreboot's definition has an extra option.
Change-Id: I0f009b21ef0850a2af6edef1818c770171358314
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67381
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The tool "include-what-you-use" analyzes each file's headers and makes
recommendations for header files to add and remove. There are
additional scripts as part of the package that will make these changes
directly based on the recommendations, but due to the way coreboot
compiles code in/out base on Kconfig options, this isn't really safe for
the project to use.
It is a good starting point though.
To use, set the IWYU kconfig option, then build with the command:
make -k
Because this doesn't actually build any files, the -k option is needed
or make will stop after looking at the first file.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: I084813f21a3c26cac1e4e134bf8a83eb8637ff63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Julius Werner <jwerner@chromium.org>
When system_uuid CBFS file is present and contains the UUID
in a string format, the driver will parse it and convert to binary
format to populate the SMBIOS type 1 UUID field.
TEST=Add UUID file and boot MSI PRO Z690-A DDR4 WIFI and check with
dmidecode if the UUID is populated correctly.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I22f22f4e8742716283d2fcaba4894c06cef3a4bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64639
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a new zydron variant, which is a variant of brya's skolas
baseboard. currently copy the variant file from kano.
BUG=b:250787251
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I49a41678568daef80b7cd1e3ed60ce4763034f9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68130
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
birman is the reference board for the morgana SoC. It needs to be
updated to match the actual board design as well.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: I4b16854c954949217a76c3d4f04ddc4001f64337
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68196
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is not critical functionality and doesn't need a build-time error.
Having it as a build time error causes a chicken & egg issue where
the chipset needs to be added before it can be added to this file, but
the header file fails the build because the chipset is unknown.
It's not practical to exclude these files from the new platform builds
because the PSP functionality is thoroughly embedded into the coreboot
structure.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: Ib02bbe1f9ffb343e1ff7c2bfdc45e7edffe7aaed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
This is an initial framework for the Morgana SoC.
TODOs have been added to the files for both customization and
commonization.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: If92e129db10d41595e1dc18a7c1dfe99d57790cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68195
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the frostflow variant of the skyrim reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:240970782
BRANCH=None
TEST=util/abuild/abuild -p none -t google/skyrim -x -a
make sure the build includes GOOGLE_FROSTFLOW
Signed-off-by: Chao Gui <chaogui@google.com>
Change-Id: I937e6562094968824e73bfa20390b3ec8b24dfa0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Write the value for reset cause registers to the EEPROM for debugging.
Change-Id: I827f38731fd868aac72103957e01aac8263f1cd3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67483
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adjust the EEPROM layout to account for two new fields: board part
number and product part number. In addition, put them in a Type 11
SMBIOS table (OEM Strings). Also, rename a macro to better reflect
its purpose.
Change-Id: I26c17ab37859c3306fe72c3f0cdc1d3787b48157
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67759
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initial commit of the FSP-specific code for the Morgana SoC.
This is just an initial framework and still needs to be updated
to match the Morgana FSP.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: Ic53c59404f96c73c55eb2648113c5ced26d6e20c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The common directory is for files that shouldn't change, or shouldn't
change much between platforms.
These will be removed from other directories and used in upcoming
commits.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: I37ed98a67b066598fdebcc5b034e64dc639fda7f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Add EC memory layout and Q events for Intel Alder Lake based boards,
the "StarBook Mk VI" and "StarFighter Mk I", which both use the ITE
5570E.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I8cea386ba91d076084002738fe7041834deea311
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add the `eeprom_read_serial()` function to read serials from the EEPROM.
Note that there's only one buffer now: this means only one serial can be
accessed at the same time, and the buffer needs to be cleared so that it
does not contain old data from other serials. Given that the serials are
copied one at a time into SMBIOS tables, having one shared buffer is not
a problem.
Change-Id: I5c9781e4e599043be756514cfd6dd86dedcf580c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67275
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PCH's SGPIO pads are connected to a buffer chip that is powered from
the always-on +3V3_AUX rail. For some cursed reason, when the SGPIO pads
stay configured as SGPIO when a Poseidon system shuts down, voltage from
the +3V3_AUX-powered buffer chip will leak into the +5V rail through the
SATA backplane. Just pulling the SGPIO pads low before the system powers
off stops the +5V rail from being cross-powered.
This issue has only been observed in S5, but it's very likely other
sleep states are affected as well. Thus, always pull the SGPIO pins
low before entering ACPI S3 or deeper because the power supply will
turn off in these states as well.
TEST=Obtain a Poseidon system, verify that the +5V rail is cross-powered
after going to S5. We measured 0.17V on our system, but voltages as
high as 0.6V were measured on other systems. Verify that unplugging
the SGPIO cable going to the SATA backplane results in the +5V rail
voltage dropping to 0V, which indicates that the voltage leakage is
exclusively coming from the SGPIO and SATA backplane. Finally, make
sure that the +5V rail voltage drops to 0V after going into ACPI S5
with this patch applied and the SGPIO cable connected.
Change-Id: Ic872903d5fcdd1c17e02b4c06d5ba29889fbc27d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
According to Intel document number 336561, GLK has UFS (0x1d),
so add the PCI interrupt.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I68bac590bd1a9a0b8213440e882c8f431f06c95f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67680
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to Intel document number 336561, G, SD Card (0x1b)
does not exist on GLK, so remove it.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I6921fc3db430c76ec54cf832ce51c627a507385c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67679
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The intention of predefining driver strength is to avoid that the OS
SD-Card driver changes this setting.
Change-Id: I02fdac94462da1cd77f8dc972faf16f28d94c946
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
To be able to change the MAC addresses, it is necessary that the
controllers are in D0 power state. As of FSP MR3, Intel has set the
controllers to D3 power state at the end of FSP-S TSN GbE
initialization. This patch sets the state back to D0 before the
programming of the MAC addresses.
Test:
- Build coreboot with FSP MR4 for mc_ehl2 mainboard
- Boot into Linux and check MAC addr via 'ip a'
Change-Id: I4002d58eb4332ba45c35d07820900dfd2c637f21
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change the TPM I2C freqeuncy to 1 MHz for pujjo.
BUG=b:249953707
TEST=On pujjo, all timing requirements in the spec are met.
Frequencies:
pujjo - 987.80 kHz
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: If99b5022a9b67e9c63c440a1e398d56bb2c467e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
apu/amdfw_a was only getting added to CBFS when VBOOT_SLOTS_RW_AB was
selected, but needs to be added in the RW_A only case as well
(VBOOT_SLOTS_RW_A). Since VBOOT_SLOTS_RW_AB selects VBOOT_SLOTS_RW_A,
we can guard amdfw_a and _b separately and both will be added in the
RW_AB case.
TEST=build google/zork with VBOOT_SLOTS_RW_A or VBOOT_SLOTS_RW_AB
selected, ensure amdfw_a and amdfw_b are added to correct CBFS regions
as appropriate.
Change-Id: Ic8048e869d7449eeb1ac10bfec4a5646b848d6a8
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68126
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
apu/amdfw should be restricted to the RO region only when building with
VBOOT + any RW region (RW_A or RW_A + RW_B); it is not tied to ChromeOS
in any way. Fix guarding to match newer AMD platforms (eg, CZN/MDN).
TEST=build google/zork without CHROMEOS, with VBOOT_SLOTS_RW_A
Change-Id: I32d7fa7a4b3d41107cfdba96128a4a75f7066c6f
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68125
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
RaptorLake introduces the support of the Voltage Regulator Fast Vmode
feature. When enabled, it makes the SoC throttle when the current
exceeds the I_TRIP threshold. This threshold should be between
Iccmax.app and Iccmax and take into account the specification of the
Voltage Regulator of the system.
This change provides a mean to:
1. Enable the feature via the `vr_config->enable_fast_vmode'. If no
I_TRIP value is supplied FSPs picks an adapted I_TRIP value for
the current SoC assuming a Voltage Regulator error accuracy of
6.5%.
2. Set the I_TRIP threshold via the `vr_config->fast_vmode_i_trip'
field.
These new fields are considered independent from the other `vr_config'
fields so that the board configuration does not have to unnecessarily
supply other VR settings to enable Fast VMode.
Information about the Fast VMode Feature can be found in the following
Intel documents:
- 627270 ADL and RPL Processor Family Core and Uncore BIOS
Specification
- 724220 RaptorLake Platform Fast V-Mode
- 686872 RaptorLake Lake U P H Platform
BUG=b:243120082
BRANCH=firmware-brya-14505.B
TEST=Read I_TRIP from the Pcode and verify consistency with
a few `enable_fast_vmode' and `fast_vmode_i_trip' settings.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: I313acf01c534d0d32620a9dedba7cf3b304ed2ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Based on DMTF SMBIOS Specification 3.5.0
Signed-off-by: Erik van den Bogaert <ebogaert@eltan.com>
Change-Id: I710124ca88dac9edb68aab98cf5950aa16c695d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67926
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
use function to check if pci device is on a particular bus
number.
TEST: compiled and qemu run successfully
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: I4a3e96381c29056de71953ea2c39cd540f3df191
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68103
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
add functions to check whether a device is enabled pci
device or a pci device on a specific bus number.
TEST: compile and qemu run successfully
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: I3257c8404017372f6cdd9f6cf9453502447343a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68101
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates scl_lcnt, scl_hcnt, sda_hold value for I2C5 to
follow I2C specification.
I2C_TCHPAD_SCL high period time is from 0.53 us to 0.6952 us.
I2C_TCHPAD_SDA hold time is from 0.13 us to 0.4623 us.
BUG=b:249031186
BRANCH=brya
TEST=EE check OK with test FW and TP function is normal.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I5977f0dbba8924cc8a1c72c36358d6ba6f2de940
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67920
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Configure eMMC DLL tuning values for Pujjo board.
BUG=b:241854926
TEST=Use the value to boot on Pujjo successfully.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: Ic36c817fa546741e394668297ca43db3a45ee105
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68095
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
An optional dGPU can be connected to the second PEG bridge:
-[0000:00]-+-00.0 Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller
+-01.0-[01]--
+-01.1-[02]----00.0 NVIDIA Corporation GK208M [GeForce GT 730M]
It's possible that the 01.0 bridge is never populated, but we have to
leave it on anyway so 01.1 can be enumerated.
Change-Id: Ieab7a7bf3b31b4ee9d9f12b5d827d866c87356e1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
